Whirlpool Refrigerator Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On Whirlpool refrigerators, PO means a power outage let the freezer warm to 18°F or higher, and a flashing F (often with an F#E# code) means the control found a fault. A blinking C points to a failed temperature sensor, and CF to a lost connection between the main board and the display. Start with a one-minute power reset; if a code returns, a technician should diagnose it.

Whirlpool refrigerators use a mix of alerts and error codes, and the exact set depends on the model and its control panel. Some displays show status lights (door alarm, filter, Cooling Off) that are reminders, not faults. Whirlpool lists its F#E# codes but does not publish what each one means for homeowners; it asks for a reset and then service, so meanings given below for those codes come from repair technicians. Unplug the refrigerator or turn off its breaker before any hands-on check. This list combines the manufacturer's own documentation with codes reported by established repair-parts references (such as Sears PartsDirect, PartSelect and repair technicians' guides); those are marked "commonly reported" or "on some models".

Whirlpool Refrigerator error codes and what they mean

Code What it means What to try
PO Power outage: power was off long enough for the freezer to reach 18°F (-8°C) or higher. An alert sounds three times. Press Measured Fill under Confirm to acknowledge it. Check food safety: discard thawed meat or anything that sat warm too long. If PO shows without a known outage, check the outlet and breaker.
Flashing F / F#E# (for example F3 E1, F3 E2, F3 E4, F3 E8, F3 E9, F3 EC, F8 EC) The control detected a fault. Whirlpool's support pages treat these codes the same way and do not publish what each one means for homeowners.
Call a technician
Turn off the breaker or unplug the refrigerator for one minute, restore power, confirm cooling is on, and watch for one minute. If the code comes back, write it down and schedule service.
C (fresh food display) On some models with a display, a blinking C in the refrigerator display means the refrigerator temperature sensor (thermistor) has failed.
Call a technician
Do a one-minute power reset. If C returns, the sensor or its wiring needs service. Keep the doors closed and use a thermometer to watch food temperatures.
C (freezer display) On some models, a blinking C in the freezer display means the freezer temperature sensor has failed.
Call a technician
Do a one-minute power reset. If it returns, request service.
CF (freezer display) On some models: the main control board is not communicating with the user interface.
Call a technician
Do a one-minute power reset. If CF returns, a technician should check the wiring between the boards and the boards themselves.
d (refrigerator display) On some models: the air damper that lets cold air from the freezer into the fresh food section is stuck.
Call a technician
Make sure food is not blocking the air vents inside. If the fresh food side stays warm while the freezer is cold, the damper needs service.
Freezer display flashing 18°F (-8°C) On older models: an over-temperature condition, often after a power failure. Make sure the power cord is firmly plugged in. Once the freezer returns to normal temperature, press a freezer temperature key to clear the display. If it stays warm, see the troubleshooting steps below.
Temperature Alarm The fresh food section has been above about 48°F (9°C) or the freezer above about 15°F (-9°C) for roughly 1.5 hours. Check for a door left ajar, blocked vents or a dirty condenser. Press Alarm to acknowledge it. Check food for spoilage. If temperatures do not recover within a day, request service.
Door Alarm / Door Ajar A door or the freezer drawer has been open for a few minutes. The alarm repeats every 2 minutes. Close all doors. Check that bins, shelves or packages are not keeping a door from sealing, and that the refrigerator is level. If it keeps sounding with doors closed, the door switch may need service.
Cooling Off Cooling is turned off (often by accident while cleaning). The lights and display work, but nothing cools. Not a fault. On many models, press and hold Lock and Measured Fill together for 3 seconds to turn cooling back on. Check your owner's manual for your model.
H2O / Water Filter light Water filter reminder (roughly every six months). Not a fault. Replace the water filter, then hold the filter reset button (often 3 seconds) until the light resets.
Air Filter light Air filter reminder on models with an air filter. The color changes as the filter ages. Not a fault. Replace the air filter and reset the indicator as shown in your manual.
F8 EC (reported meaning) Whirlpool does not publish a meaning. Technicians commonly report it as the ice maker module being stalled or stuck, so the control cannot move it.
Call a technician
Check that ice is not jammed in the ice maker or bin, then reset the refrigerator for one minute. If F8 EC returns, call a technician.
E1 / F1 (some models) Commonly reported as a temperature sensor (thermistor) fault: the sensor has failed, come unplugged or is buried in frost.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
E3 / F3 (some models) Commonly reported as a defrost system fault: a defrost heater, defrost thermostat or control problem.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
SY CE (some models) Reported mainly on non-US Whirlpool models: communication lost between the user interface and the main control board.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
rd / DF (some models) Reported mainly on non-US Whirlpool models: defrost heater circuit problem (rd) or defrost failure (DF).
Call a technician
Look for heavy frost on the back wall of the freezer. Unplug for one minute; if the code returns or frost builds again, call a technician.
PC (some models) Pantry drawer temperature sensor error on models with a temperature-controlled drawer.
Call a technician
Turn off power at the breaker (or unplug) for 5 minutes, then restart. If the code comes back, call a technician.
6 / flashing 6 (older models) Older electronic models: a steady 6 is listed as a control (computer) error; a flashing 6 usually clears once the fridge returns to temperature.
Call a technician
Give the refrigerator a few hours to recover with the doors closed. If 6 stays on, reset the power once and call a technician if it returns.
01 on display Diagnostic (service) mode is active. Not a fault. Exit by following your tech sheet, or reset the power for one minute.

What we actually find on Whirlpool refrigerators in the Denver area

The codes above come from Whirlpool’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 127 Whirlpool refrigerator service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The Whirlpool refrigerator repairs we do most often

Across all 127 Whirlpool refrigerator calls, with or without a code on the display:

  1. Evaporator or condenser fan: 12 calls
  2. Ice maker: 11 calls
  3. Control or inverter board: 9 calls
  4. Defrost system: 5 calls
  5. Compressor or sealed system: 5 calls
  6. Thermistor or sensor: 3 calls
  7. Water inlet valve: 2 calls

Recent Whirlpool refrigerator calls

  • Boulder (80301), October 2026: Whirlpool refrigerator freezer not freezing. Diagnosis: evaporator or condenser fan.
  • Lakewood (80226), September 2026: Whirlpool refrigerator ice maker not working. Repair: water inlet valve replaced.
  • Erie (80516), July 2026: Whirlpool refrigerator ice maker not working. Repair: ice maker replaced.
  • Broomfield (80020), July 2026: Whirlpool refrigerator ice maker not working. Repair: ice maker replaced.

Whirlpool refrigerator repairs from $260. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Whirlpool refrigerator evaporator or condenser fan repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a evaporator or condenser fan repair. It is the most common refrigerator repair on our calls.
  • The Whirlpool refrigerator repairs we do most often across the Denver metro and Boulder County: evaporator or condenser fan (12 calls), ice maker (11) and control or inverter board (9).
  • Recent call: Lakewood (80226), September 2026: Whirlpool refrigerator ice maker not working. Repair: water inlet valve replaced.

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. For any flashing F or F#E# code, unplug the refrigerator or turn off its breaker for one minute, then restore power.
  2. Make sure cooling is on and not set to Cooling Off.
  3. Close and check all doors; make sure nothing blocks the seals and that the unit is level.
  4. Keep food away from the air vents inside both compartments.
  5. With the refrigerator unplugged, vacuum dust from the condenser coils and grille at the bottom.
  6. Use a thermometer to confirm temperatures: about 37°F in the fresh food section and 0°F in the freezer.

When to call a technician

  • A flashing F or F#E# code returns after a power reset.
  • C, CF or d appears on the display.
  • The refrigerator or freezer stays warm for more than a day after you clear vents and clean the coils.
  • You hear the compressor clicking on and off, or nothing runs at all.
  • Frost builds up on the back wall of the freezer, which can point to a defrost problem.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I reset a Whirlpool refrigerator error code?

Turn off the breaker or unplug the refrigerator for one minute, then restore power and make sure cooling is on. If the code returns within a minute or two, the fault is still there and needs service.

What does PO mean on a Whirlpool refrigerator?

PO means there was a power outage and the freezer warmed to 18°F or higher. Press Measured Fill under Confirm to clear it, then check your food for safety.

Why does my Whirlpool fridge say Cooling Off?

Cooling has been switched off, often by accident during cleaning. On many models, holding Lock and Measured Fill together for 3 seconds turns it back on.

Are SY EF or SY CE Whirlpool refrigerator codes?

SY EF and SY CE do not appear in Whirlpool's US refrigerator support pages. Repair references list SY CE (a communication error between the display and main board) mainly for non-US Whirlpool models, and SY EF is usually a Frigidaire code. If you see a code not listed here, check the tech sheet for your exact model.

Sources: producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, searspartsdirect.com, ifixit.com, appliancepartspros.com, ifixit.com, justanswer.com, removeandreplace.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229

Photos from our job records

Real photos our technicians took on repair calls around Denver and the Front Range. Each caption says where the job was.

Refrigerator repair in Littleton, photo from our job records
Refrigerator repair in Littleton
Refrigerator repair in Thornton, photo from our job records
Refrigerator repair in Thornton
Refrigerator repair in Thornton, photo from our job records
Refrigerator repair in Thornton
Refrigerator repair in Lafayette, photo from our job records
Refrigerator repair in Lafayette
Call Now Book Online