Whirlpool Oven & Range Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On Whirlpool ranges, F1 codes point to the oven control, F2 to the keypad, F3 to the oven temperature sensor, F5 to the door lock, F6 to overheating or a control mismatch, F8 to the cooling fan, and F9E0 to miswired power. Turn the breaker off for one minute and back on; if the code returns, Whirlpool recommends service. LOC, PF, SAb, H and ES are messages, not faults.

Whirlpool ranges and wall ovens show a two-part code: the F number names the system and the E number gives the detail (for example F3E0, oven sensor open). Some models show the same faults as 1C, 1d, 3d, 4d or 9d codes, and older models use single F codes. This list combines Whirlpool's help pages and service manual with codes documented by parts references. Codes vary by model, so check your owner's manual if yours is not listed.

Whirlpool Oven & Range error codes and what they mean

Code What it means What to try
F1 / F01 to F06 / F1-1 to F1-L Whirlpool help pages tie these to the oven temperature sensor, the oven control, or their wiring.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F0 / F0E0 On many models F0 means no fault is stored (shown when Cancel is held for 5 seconds). F0E0 is listed by Whirlpool without a public meaning. Control-detected fault. Reset power at the breaker for a minute (or unplug for 5 minutes); if it returns, call a technician.
F1E0 / F1E1 / F1E2 Oven control board fault: EEPROM communication or checksum error, or A/D (internal reading) error. On some wall ovens F1E0 points to the control panel (user interface).
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F1E3 / F1E4 Commonly reported as a wiring harness that does not match the stored oven size (F1E3) or a model ID error (F1E4), often after a control replacement.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F1E5 / F1E6 Sensor reading out of range or calibration shifted (F1E5); latch signal mismatch (F1E6).
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F1E7 / F1E9 Control board fault: board thermistor open or shorted (F1E7) or internal software error (F1E9).
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F2E0 Keypad disconnected or not responding. Some parts references list it as a shorted touch pad.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F2E1 Stuck or shorted key. Some parts references list it as an unplugged touch pad cable.
Call a technician
Wipe the panel dry and press Cancel. Reset power at the breaker. If it returns, the keypad or control usually needs replacing.
F2E2 / F2E5 / F2E6 Cancel key error or Cancel key circuit open.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F2E3 / F2E4 Keypad or user interface problem, or its wiring.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F3E0 / F3E1 Oven temperature sensor open (F3E0) or shorted (F3E1). On double wall ovens, F3E1 can mean the lower oven sensor.
Call a technician
Reset power at the breaker once. If the code comes back, a technician should test the sensor and its wiring.
F3E2 Depending on control: bake or broil temperature too high (over about 575°F), or a warming drawer sensor fault.
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
F3E3 Depending on model: oven too hot in self-clean (over about 950°F), or a meat probe fault on some wall ovens.
Call a technician
Turn the oven off and let it cool. If you use a meat probe, unplug it. Reset power; if it returns, request service.
F3E4 / F4E1 Meat probe or probe jack fault (shorted probe). Make sure the meat probe is fully seated, or unplug it and cook without it. If the code stays, request service.
F5E0 / F5E2 Door switch and door lock switch do not agree, usually around a self-clean cycle.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
F5E1 Door latch (lock) is not operating; it will not lock or unlock.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
F5E3 / F5E4 Lower oven door and latch switch do not agree (F5E3) or lower latch not operating (F5E4) on double ovens; on single ovens F5E3 is a main oven door latch or switch fault.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
F5E5 / F5E7 Door latch, door switch or wiring fault.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
F6E0 Communication lost between the user interface and the oven control. Some references list it as a return line not connected.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F6E1 Oven over temperature while cooking (above about 600°F). The oven locks out until it cools.
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
F6E2 / F6E3 Over temperature in self-clean (F6E2), or in the warming drawer or lower oven (F6E3).
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
F6E4 / F6E5 / F6EA User interface and control do not match or are not programmed for this oven, or a user interface wiring fault. Often seen after a part replacement.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F7E0 / F7E1 Door latch assembly (F7E0) or door switch common wire (F7E1) problem.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
F7E5 Cooling fan or fan wiring problem.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F8E0 / F8E2 Cooling fan speed too low (F8E0) or too high (F8E2), or a fan wiring problem.
Call a technician
Make sure nothing blocks the vents. Reset power at the breaker. If it returns, do not run long bakes or self-clean; request service.
F8EA User interface (control panel) or its wiring.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F9E0 House power or range is miswired, or a voltage glitch at power-up.
Call a technician
If the range was just installed, have the installer or an electrician check the power connection. Otherwise reset power once; if it returns, request service.
FEE6 / FEE7 Bake element (FEE6) or broil element (FEE7) circuit problem in the main oven.
Call a technician
Turn off the breaker before looking at the elements. If an element is visibly broken or blistered, it needs replacing. Otherwise reset power; if it returns, request service.
FEE8 / FBE1 / FBE2 Control-detected fault with no specific part named in the manufacturer help pages.
Call a technician
Control-detected fault. Reset power at the breaker for a minute (or unplug for 5 minutes); if it returns, call a technician.
FC E1 (and FC E2 to FC E9) Connected models: FC E1 means the oven could not connect to the home Wi-Fi router. Other FC codes are listed without public meanings. Reset power, then reset your router and check Wi-Fi signal near the range. Cooking functions are not affected by Wi-Fi.
F2E0 to F5E1 (two-part display, e.g. F3/E0) Some ranges show the same codes split across the display, such as F3/E0 for an open sensor or F5/E1 for a latch that will not lock. Read the two parts together and match them to the codes above.
F7E6 Listed by Whirlpool without a public meaning.
Call a technician
Control-detected fault. Reset power at the breaker for a minute (or unplug for 5 minutes); if it returns, call a technician.
F8 Meat probe problem on some models. Make sure the meat probe is fully seated, or unplug it and cook without it. If the code stays, request service.
F9-1 / F9-2 / F9-3 Oven door latch, door lock switch or wiring problem.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
1C/1C, 1C/2C Two-part display codes: stuck key or defective keypad (1C/1C), or keypad harness unplugged (1C/2C).
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
1C/31, 1C/32, 1C/4C, 1C/6C, 1C/7C, 1C/8C, 1C/81, 1C/82 Two-part display codes: oven control board, Cancel key circuit or communication fault.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
1d/11, 1d/12, 1d/21, 1d/22 Oven too hot in Bake or Broil (1d/1x) or in Clean (1d/2x).
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
3d/11 to 3d/51 Oven temperature sensor fault (3d/11, 3d/12, 3d/21, 3d/22 listed by parts references; other 3d codes listed by the manufacturer).
Call a technician
Reset power at the breaker once. If the code comes back, a technician should test the sensor and its wiring.
4d/11 to 4d/52 Oven door switch and door lock switch disagree, or a door latch or wiring fault.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
9d/11 to 9d/62 Oven door lock assembly fault; 9d/31 and 9d/32 occur in Clean mode.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
F0 / F1 / F5 / F8 (older 2-digit controls) Older controls: oven control board failure (F5 watchdog conflict, F8 analog/digital error). On some newer controls F0 simply means no stored faults.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F2 (older 2-digit controls) Older controls: oven temperature too high.
Call a technician
Turn the oven off at the breaker and let it cool. Do not use it until it is checked; a sensor, relay or control fault can cause runaway heat.
F3 / F4 (older 2-digit controls) Older controls: oven temperature sensor open or shorted (references differ on which is which).
Call a technician
Reset power at the breaker once. If the code comes back, a technician should test the sensor and its wiring.
F7 (older 2-digit controls) Older controls: function key stuck or shorted.
Call a technician
Turn the power off at the breaker for about a minute, then back on. If the code returns, request service.
F9 (older 2-digit controls) Older controls: oven door latch or lock switch problem.
Call a technician
Let the oven cool completely, then reset power at the breaker for a minute. Do not force the door. If the code returns or the door stays locked, request service.
C81 / C82 / C83 The cooktop surface overheated and its automatic shutoff turned on. Turn the cooktop off and let it cool about 5 minutes. If it returns, reset power; if it persists, request service.
H A cooktop surface is still too hot to touch. Not a fault. Let it cool. If H stays on with a cold cooktop, reset power; if it persists, request service.
ES Energy Save mode turned the display off (some models). Not a fault. Press and hold Clock for 10 seconds to exit, or reset power.
PF / flashing time A power failure occurred. Press Cancel and reset the clock.
LOC / Lock / Locked Control lock is on. Not a fault. Unlock the controls using the steps in your owner's manual.
SAb / 5Ab Sabbath mode is on. Not a fault. Exit Sabbath mode using the steps in your owner's manual.

What we actually find on Whirlpool ovens in the Denver area

The codes above come from Whirlpool’s own documentation. This section shows what our technicians found once they opened the machine. Since 2024 we have handled 45 Whirlpool oven service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

Code Our calls What we found
F3 2 Most often: control board. Also seen: temperature sensor.
E2 1 Control board.

The oven repairs we do most often (all brands)

Our notes on Whirlpool ovens are too thin to rank by brand alone, so here is what we found across all 645 oven calls in our records:

  1. Control board: 54 calls
  2. Igniter: 45 calls
  3. Bake or broil element: 26 calls
  4. Surface element or burner switch: 20 calls
  5. Wiring: 16 calls
  6. Convection fan: 15 calls
  7. Temperature sensor: 13 calls

Recent Whirlpool oven calls

  • Parker (80134), May 2026: Whirlpool oven not heating. Repair: bake or broil element replaced (W11182108).
  • Superior (80027), March 2026: Whirlpool oven not starting. Repair: gas valve or safety valve replaced (W11511824).
  • Erie (80516), September 2025: Whirlpool oven showing F3. Repair: temperature sensor replaced.
  • Erie (80516), April 2025: Whirlpool oven showing E2. Repair: control board replaced.

Whirlpool oven repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2024–2026. Customer details removed.

Video: Whirlpool oven error codes

Video by AppliancePartsPros

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 645 oven calls in our records (all brands), the repairs we do most often: control board (54 calls), igniter (45) and bake or broil element (26).
  • Recent call: Parker (80134), May 2026: Whirlpool oven not heating. Repair: bake or broil element replaced (W11182108).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Turn the range off at the circuit breaker for about one minute, then back on, and watch the display for a minute.
  2. Wipe the control panel dry; moisture can trigger stuck-key codes.
  3. Make sure the meat probe is fully seated, or remove it, for probe codes.
  4. Let the oven cool fully before trying the door or self-clean again.
  5. Keep vents around the cooktop and oven clear for cooling fan and overheat codes.
  6. On gas models, never adjust gas connections yourself. If you smell gas, leave and call the gas utility.

When to call a technician

  • Any F code returns after a one-minute breaker reset.
  • The oven overheats (F6E1, F3E2, 1d codes) or keeps heating when off.
  • The door stays locked after the oven has cooled.
  • F9E0 appears on a range that has not just been installed, or you smell gas or burning.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I clear an error code on my Whirlpool oven?

Turn off the circuit breaker for the range for about one minute, then turn it back on and watch the display for a minute. If the code stays gone, the oven is fine to use; if it returns, request service.

What does F3E0 mean on a Whirlpool oven?

F3E0 means the oven temperature sensor reads open or out of range. The sensor or its wiring usually needs to be tested and replaced.

What does F2E1 mean on a Whirlpool range?

F2E1 means the control sees a stuck or shorted key. Dry the panel and reset power; if it returns, the keypad or control needs replacing.

What does F9E0 mean?

F9E0 means the range or the house power is miswired, or a voltage glitch happened at power-up. On a new installation, have the power connection checked before using the range.

Sources: producthelp.whirlpool.com, producthelp.whirlpool.com, whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, producthelp.whirlpool.com, whirlpool.com, searspartsdirect.com, searspartsdirect.com, partselect.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online