Amana Dryer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Three codes cover most Amana dryer calls: AF (also F4E3) for a blocked lint path, L2 (also F4E4) for missing voltage that leaves the dryer cold, and PF after a power interruption. Clean the screen and the vent and reset both breakers before anything else. Alternating F#E# codes and the plain E1, E2 and E3 codes are faults the control found: give it five minutes without power, and call a technician if they come back.

Amana dryers with a display use Whirlpool’s code system, since Whirlpool owns the brand. Amana explains the airflow, voltage and power messages but publishes most F#E# and E codes without meanings, so those definitions come from Whirlpool-platform service material and repair references. Expect small differences between models. Unplug the dryer before you inspect it; on gas models close the gas shutoff and do not touch the burner.

Amana dryer codes

Messages Amana explains

Code What the Amana is flagging Try first
AF, F4E3, F4 E3 Exhaust is restricted: full screen, clogged or crushed duct, or a long run with many turns. It keeps tumbling but dries slowly. Empty the screen, unplug, and clear the duct out to the wall hood. Make sure the hood flap swings open. Any key clears the code.
L2, F4E4 Electric dryers: one leg of the 240 V supply is low or dead, so no heat. Most common right after installation.
Technician
Check both breakers or fuses and that the cord was installed per the instructions. Run a timed heated cycle; if it persists, call an electrician.
PF Power cut during the cycle. Touch and hold Start to resume, or press Power to clear.
Alternating F# / E# The control found a fault needing service; specific codes below.
Technician
Kill power for five minutes, then a short Timed Dry. If it reappears, book a repair.

Codes Amana lists without a definition

Code What the Amana is flagging Try first
E1, E2 On Whirlpool-platform electronic dryers, reported as thermistor failures.
Technician
Kill power for five minutes, then a short Timed Dry. If it reappears, book a repair.
E3 Reported as a board and interface mismatch, usually after a part replacement.
Technician
Verify the replacement part number.
F1E1 Main board fault, on some models a stuck motor relay.
Technician
Kill power for five minutes, then a short Timed Dry. If it reappears, book a repair.
F1E3 Wrong board installed.
Technician
Match the board to your model number.
F1E4 Control unit or its wiring.
Technician
Five minutes off, then watch a timed cycle for five minutes.
F2E1, F2E2 Keypad or control, often a stuck key.
Technician
Press keys firmly, one-minute power reset.
F2E4, F2E5 Interface software error.
Technician
Kill power for five minutes, then a short Timed Dry. If it reappears, book a repair.
F3E1 Exhaust thermistor.
Technician
Clean the lint path first.
F3E2 Moisture sensor; sensor-dry cycles end early or run long. Clean the drum sensor bars with rubbing alcohol and keep metal off them. Use Timed Dry meanwhile.
F3E3 Inlet thermistor near the heat source.
Technician
Kill power for five minutes, then a short Timed Dry. If it reappears, book a repair.
F4E1, F4E2 Heater relay failure; the dryer may stay cold.
Technician
Kill power for five minutes, then a short Timed Dry. If it reappears, book a repair.
F6E2, F6E3 Board and interface stopped communicating.
Technician
Usually a harness or board.

What we actually find on Amana dryers in the Denver area

The codes above come from Amana’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 7 Amana dryer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The dryer repairs we do most often (all brands)

Our notes on Amana dryers are too thin to rank by brand alone, so here is what we found across all 983 dryer calls in our records:

  1. Heating element: 88 calls
  2. Drive belt: 35 calls
  3. Idler pulley or drum rollers: 33 calls
  4. Clogged vent or lint: 29 calls
  5. Thermal fuse or thermostat: 27 calls
  6. Control board: 26 calls
  7. Thermistor or sensor: 20 calls

Dryer repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Amana dryer heating element repair

Video by Parts Dr

What we see on Denver calls

  • The video shows a heating element repair. It is the most common dryer repair on our calls (all brands).
  • Across all 983 dryer calls in our records (all brands), the repairs we do most often: heating element (88 calls), drive belt (35) and idler pulley or drum rollers (33).

Don’t want to do it yourself? Call 720-230-1229.

Do these before booking

  1. Unplug the dryer; on gas units leave the gas parts alone.
  2. Wash the lint screen in warm soapy water if it looks glazed.
  3. Clear the duct and replace any crushed foil hose.
  4. No heat on an electric dryer? Reset both breakers.
  5. Wipe the moisture bars and run one timed cycle.

Call us if

  • An F#E# or E code returns after a five-minute power cut.
  • It tumbles cold even with good breakers and a clear vent.
  • AF keeps appearing after the screen and vent are clean.
  • You smell gas or burning, or clothes come out scorched.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Amana dryer code FAQ

What does AF mean on an Amana dryer?

Airflow is restricted. Clean the lint screen and the full vent run.

How do I reset an Amana dryer?

Switch off the breakers or unplug it for five minutes, then start a timed cycle.

Why does my Amana show L2 and not heat?

One leg of the 240-volt supply is missing. Check both breakers and the cord connection.

Sources: producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.whirlpool.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online