Amana Washer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

On an Amana washer, LF / Lo FL / F8E1 means filling takes too long, drn / Ld / F9E1 means draining takes too long, LdL or F5E2 means the lid will not lock, Lid or F5E4 means the lid was left open, OFb, uL or OL means the load is off balance or too big, and Sud or Sd means too much foam. Open both faucets, check the drain hose, rearrange the load and measure HE detergent. Codes in the F1, F3, F6 and F7 families involve the boards, sensors, motor or shifter and usually need a technician.

Amana washers are Whirlpool products and use the F#E# system alongside short text messages such as LF and Sud. Many Amana top-loaders have no display and signal problems with lights instead; we cover those at the end. Amana’s support site lists a lot of codes without explaining them, so some definitions here come from Whirlpool documentation for the same platform and from repair references, and a few vary by model. Before touching anything, unplug the washer and close both water valves.

Amana washer codes, sorted by what went wrong

Fill and water temperature

Code Amana washer meaning Fix to try
LF, Lo FL, F8E1 Fill is too slow. Both faucets open, both hoses on, no kinks, no anti-flood device in the line. With the water off, clean the inlet screens.
HC, F8E5 Hot and cold hoses swapped; appears at the end of the wash. Water off, swap the hoses, run again.
F8E6 Model dependent: lid open during a soak, or no hot water detected. Close the lid; check faucets and hose order.
F8E3 Overflow: too much water in the tub.
Technician
Close the valves. Water entering with the washer off means a stuck inlet valve.
F0E4 Top-loaders: rinse water too hot, so spin was slowed. Check the hoses are not reversed.

Drain and suds

Code Amana washer meaning Fix to try
drn, Ld, F9E1 Drain is too slow, about 8 minutes or more. Unkink the hose. It should go no more than 4.5 inches into the standpipe, with its end above 36 inches so it cannot siphon. Front-loaders: clean the pump filter.
F0E8 Water left in the tub. Run Drain and Spin and check the hose.
Sud, Sd, 5d, F0E2 Excess foam; the washer pauses and adds rinses. Measure HE detergent and skip no-splash bleach, which foams.

Lid and lock

Code Amana washer meaning Fix to try
LdL, dL, dLO, F5E2, Lid light blinking Lid or door will not lock. Clear anything under the lid and wipe lint or soap off the striker. Let the lock self-test finish without lifting the lid.
LdU, dU, F5E3 Lid will not unlock, usually because something sits on top. Remove the basket. Still locked with nothing on it? Service.
Lid, F5E4 Lid left open, or not opened between loads. After 10 minutes the cycle resets and drains. Close it to continue; open and close between loads.
F5E1 Lid or door switch fault.
Technician
Unplug five minutes and run again; if it repeats, schedule service.

Load, dispenser and Clean Washer

Code Amana washer meaning Fix to try
OFb, uL, F0E5, several lights blinking Unbalanced load (on display-free top-loaders, multiple blinking lights usually mean this). Let it rebalance; if it stops, even out the load. Use Bulky/Sheets for comforters.
OL, F0E3 Too much laundry; water and detergent are drained. Take items out, add detergent again, close the lid, restart.
F0E9, F0E0 F0E9 is commonly reported as balance-related on Whirlpool-platform top-loaders; F0E0 has no published meaning. Redistribute and restart; unplug five minutes and run again; if it repeats, schedule service.
F8E2 Select front-loaders: dispenser system problem. Soak out hardened detergent from the drawer or cartridge.
F3E5 Select top-loaders: mini dispenser problem. Put detergent straight into the drum for now.
F0E7, rL, F34 Items found in the drum during Clean Washer. Empty it and restart Clean Washer.

Motor, shifter, sensors and controls

Code Amana washer meaning Fix to try
F7E1 Drum not reaching the expected speed (speed sensing).
Technician
New install? Shipping bolts out. Do not overload.
F7E4, F7E5 Shifter fault: the part that switches between agitate and spin.
Technician
Unplug five minutes and run again; if it repeats, schedule service.
F7E0, F7E2, F7E6, F7E7, F7E9 Drive faults on the Whirlpool platform: motor failure (E2, E6), motor below speed (E7) and others.
Technician
Try a smaller load after a five-minute unplug.
F3E1, F3E2, F3E3 Water level pressure sensor (E1), water temperature sensor (E2); E3 has no published meaning.
Technician
Unplug five minutes and run again; if it repeats, schedule service.
F1E1, F1E2 Main board (E1) or motor control (E2).
Technician
Unplug five minutes and run again; if it repeats, schedule service.
F2E1 to F2E5 Stuck key (E1), keypad (E2), board and interface mismatch (E3), interface errors (E4, E5).
Technician
Press each key firmly; unplug five minutes.
F6E1, F6E2, F6E3 Boards not communicating.
Technician
Usually a harness or board.

Messages that are not faults, and display-free models

Code Amana washer meaning Fix to try
Err Front-loaders: an action was refused, such as changing cycles mid-run or starting with the door open. Stop the washer before changing settings; close the door before Start.
Int, PF Cycle paused or cancelled (Int, may drain 20 to 30 minutes); power failure (PF). Int: wait, Pause/Cancel twice, Power once. PF: hold Start.
LOC, LC, dET, Fd Control lock (LOC, LC), cartridge not detected (dET), factory reset (Fd). Hold Control Lock; reseat the cartridge; Fd clears in 3 seconds.
Wash/Fill light on, Spin light blinking Top-loaders without a display: fill problem (Wash or Fill), drain or balance problem (Spin). Faucets and hoses for the first, drain hose and load for the second.

What we actually find on Amana washers in the Denver area

The codes above come from Amana’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 12 Amana washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The washer repairs we do most often (all brands)

Our notes on Amana washers are too thin to rank by brand alone, so here is what we found across all 1238 washer calls in our records:

  1. Control or display board: 108 calls
  2. Drain pump: 74 calls
  3. Shock absorbers or suspension: 57 calls
  4. Water inlet valve: 41 calls
  5. Door or lid lock: 28 calls
  6. Door boot seal: 27 calls
  7. Drive belt or coupler: 23 calls

Recent Amana washer calls

  • Longmont (80504), June 2026: Amana washer not draining. Repair: drain pump replaced.
  • Arvada (80007), May 2026: Amana washer not starting. Repair: pressure or water-level sensor replaced (W11607637).

Washer repairs from $240. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Amana washer error codes

Video by Parts Dr

What we see on Denver calls

  • An error code points to the system that reported the fault, not always to the part that failed.
  • Across all 1238 washer calls in our records (all brands), the repairs we do most often: control or display board (108 calls), drain pump (74) and shock absorbers or suspension (57).
  • Recent call: Longmont (80504), June 2026: Amana washer not draining. Repair: drain pump replaced.

Don’t want to do it yourself? Call 720-230-1229.

Amana washer checks

  1. Unplug and close both water valves.
  2. Reopen the faucets fully; clean the inlet screens.
  3. Check drain hose depth (4.5 inches max) and height (36 inches min).
  4. Clear the lid area and the lock striker.
  5. Even out the load and measure HE detergent.

When to bring in a technician

  • An F1, F3, F6 or F7 code returns after a reset.
  • It still will not drain with a clear hose and filter.
  • F8E3, or water entering while the washer is off.
  • The lid stays locked with nothing on it, or there is grinding, banging or a burning smell.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Amana washer code FAQ

How do I reset an Amana washer?

Unplug it for five minutes, plug it back in and start a cycle.

What does LF mean?

The washer is filling too slowly. Check the faucets, hoses and inlet screens.

Why is the Lid light blinking?

The lid did not lock. Clear anything in the way and let the lock test finish.

Several lights are blinking on my display-free Amana. Why?

On top-loaders without a display, that usually signals an unbalanced load.

Sources: producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.amana.com, producthelp.whirlpool.com, searspartsdirect.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online