A Whirlpool or Maytag dryer that tumbles but doesn’t heat usually has one of three problems: an electric dryer has lost one leg of its 240-volt power, a heating part has failed (heating element, thermal fuse or thermostat), or on a gas dryer the igniter or gas valve coils have quit. Maytag dryers are built by Whirlpool Corporation and share most of these parts, so the diagnosis is the same. Dryers account for about 1,400 jobs in our records since late 2023. Here is how to narrow it down.
At a glance
- First, make sure you aren’t on Air Only or Air Fluff; those cycles don’t heat.
- Electric dryers need two breakers on a 30-amp, 240-volt circuit. One tripped breaker can mean it runs but doesn’t heat.
- On one common Whirlpool electric model, the parts that most often fix “no heat” are the heating element (42%) and the thermal fuse (22%), according to PartSelect’s repair data.
- A blown thermal fuse is a symptom. The cause is usually a clogged vent.
- Heating element, thermal fuse, thermostat or gas igniter replacement: from $179 in labor.
Step 1: Rule out the cycle and the power
Whirlpool’s own first check is to run a heated, timed cycle empty for 5 minutes, then feel inside the drum. Make sure the cycle isn’t Air Only or Air Fluff, which don’t use heat.
For electric dryers, Whirlpool notes they use two breakers on a 30-amp, 240-volt circuit, and if either one trips the dryer may not heat. Check both breakers in the panel, and reset any that look tripped by switching fully off, then on. The motor runs on one leg of the supply and the heater needs both, which is why a dryer can tumble normally with no heat. Repair Clinic notes normal outlet voltage is about 210–240 volts.
For gas dryers, Whirlpool says to confirm the gas shutoff valve behind the dryer is open, with the handle parallel to the pipe. With the valve closed, the drum turns but there’s no heat.
Step 2: Check the vent
A restricted vent doesn’t just slow drying; it is one of the most common reasons heating parts fail. Lint and hot air back up, the dryer overheats, and the safety devices shut the heat off. Pull the dryer out, look for a crushed or kinked duct, and go outside to make sure the vent flap opens and air flows strongly when the dryer runs. Whirlpool advises cleaning the vent every one to two years, and NFPA recommends cleaning lint out of the vent pipe at least once a year. Read our guide to dryer vent cleaning for the warning signs.

Step 3: The usual failed parts on electric dryers
PartSelect publishes which parts fixed “not heating” on specific models. For one common Whirlpool electric dryer (WED4616FW0), the breakdown was:
| Part | Share of “no heat” fixes | What it does |
|---|---|---|
| Heating element (240V, 5400W) | 42% | The coil that makes the heat. Breaks open with age or overheating. |
| Thermal fuse | 22% | One-time safety fuse that blows when exhaust gets too hot. |
| Cycling thermostat | 12% | Turns the heat on and off to hold drying temperature. |
| Thermal cut-off kit | 11% | High-limit safety that cuts heat if the heater box overheats. |
| High-limit thermostat | 9% | Another overheat safety on the heater housing. |
| Heating element connection wire kit | 3% | Burned or loose terminals at the element. |
Other models differ, but the pattern holds across Whirlpool and Maytag electric dryers: the element and the safety devices around it fail most. A technician confirms which one with a meter rather than replacing parts on a guess.
Why the thermal fuse keeps blowing: PartSelect notes the thermal fuse blows when exhaust temperature exceeds its rating, usually because of a restricted vent, a plugged lint screen or a broken blower wheel. Replace the fuse without fixing the airflow and it will blow again.
Step 4: Gas dryer parts
On gas models, watch through the small window near the burner (or listen) during a heated cycle. Repair Clinic’s guidance on the usual suspects:
- Igniter doesn’t glow: the igniter, the flame sensor or a thermal safety is likely open.
- Igniter glows, then shuts off without lighting: the gas valve solenoid coils are likely failing.
Gas work should be done by a qualified technician. If you smell gas, shut off the valve, leave the house and call your gas utility. Altitude can make gas dryers in Denver run slightly longer cycles; more on that in how Denver’s altitude affects your appliances.
Repair costs
For Whirlpool and Maytag dryers, our starting labor prices are: thermal fuse, thermostat, heating element or gas igniter from $179; belt, rollers, idler pulley, drive motor or control board from $259. Parts are listed separately in your quote, and the service call (from $59) is waived when you approve the repair. Full details are on our pricing page. Because dryers are simple machines, a no-heat repair is almost always worth doing, even on an older dryer.
See Whirlpool dryer repair, Maytag dryer repair, or our general dryer not heating guide.
What our service calls show
In our own service records, Whirlpool electric dryers that do not heat most often need the heating element WP3387747 (12 of 29 Whirlpool no-heat calls), followed by thermistors (WP8577274) and badly clogged vents. Maytag is similar: the element came up in 13 of 30 calls, WP8544771 on front-load-style models and WP3387747 or WPY313538 on standard models.
Samsung dryers follow the same pattern: see Samsung dryer not heating. If the dryer heats but the clothes take too long, start with the vent: dryer takes too long and dryer vent cleaning. The full brand-by-brand breakdown is in our guide to dryers not heating.
Frequently asked questions
Why is my Whirlpool dryer running but not heating?
On electric models, a tripped breaker on one leg of the 240-volt supply, a failed heating element or a blown thermal fuse are the most common causes. On gas models, check that the gas valve is open, then the igniter and gas valve coils.
Where is the thermal fuse on a Whirlpool or Maytag dryer?
It is usually mounted on the blower housing or exhaust duct at the back of the dryer, behind the rear panel. Unplug the dryer before removing any panels.
Why does my dryer keep blowing thermal fuses?
Almost always because of restricted airflow: a clogged or crushed vent, a full lint screen or a damaged blower wheel. The vent needs to be fixed along with the fuse.
Are Maytag and Whirlpool dryers the same?
Maytag is a Whirlpool Corporation brand, and many Maytag and Whirlpool dryers share the same heating parts, so diagnosis is the same. Always match replacement parts to your exact model number.
How much does it cost to fix a dryer that won’t heat?
With us, replacing a heating element, thermal fuse, thermostat or gas igniter starts at $179 in labor plus the part.
Keep Exploring
Get it fixed
Dryer repair by city
Troubleshooting guides
Maintenance guides
Error codes by brand
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't: