Frigidaire Washer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

Most Frigidaire washer codes come down to five things: water arriving too slowly (E11, top-load E1), water leaving too slowly (E21, EF1, top-load E2), the door lock (E41 to E48), an off-balance load (top-load E4) and too much foam (EF2). Opening the valves, emptying the pump filter, evening out the load and using less HE detergent clear many of them. Motor (E52 to E5F), heater (E66, E68), sensor and board codes call for a technician.

The E-codes here apply mainly to Frigidaire front-loaders with a digital display built from about 2014 on. Older front-loaders such as the Affinity line, top-loaders and stacked laundry centers use some different codes, which have their own tables below. When a code does not match, your owner’s manual or the tech sheet behind the panel wins. Unplug the washer and turn off both water valves before you inspect anything. Codes labelled “commonly reported” come from repair references rather than Frigidaire’s own documents.

Frigidaire washer codes

Front-load: water level, fill and drain

Code Frigidaire meaning First move
E11 Filling takes too long. Open both valves, check hoses for kinks or ice, clean the inlet screens with the washer unplugged. Do not shove the drain hose deep into the standpipe; it can siphon.
E21 Draining too slowly. Unplug, put towels down and clean the pump filter behind the lower front panel. Check the hose and the house drain.
EF1 Drain pump clogged. Clear the pump filter; a pump that still will not pump is replaced.
EF2, F2, EF0 Suds overload (EF0 is listed by some references as no hot water instead). Less HE detergent; hard Front Range water tempts people to add more, which makes it worse. Run a rinse.
E13 Tub leak, or an air leak in the pressure sensor hose.
Technician
Look under the washer for water.
E31, E32, E38 Pressure sensor not communicating (E31, E32) or its air trap clogged (E38).
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
E35 Overfill.
Technician
Water off. Filling while unplugged means a stuck inlet valve.
E23, E24 Drain pump relay on the board failed, or a pump wire is off.
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
E10, E20, E30, E40, E50 Commonly reported on some front-loads: no fill (E10), no drain (E20), overfill (E30), door open (E40), motor overheated (E50).
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
E14 Dispenser drawer not detected as closed. Push the drawer all the way in.

Front-load: door lock

Code Frigidaire meaning First move
E41 Door reads open. Close it firmly with no clothing in the seal.
E43, E45, E47, E48, E4A Lock circuit fault; E47 means it opened during spin.
Technician
Power off and restart once.
E36, E44, E46 Control board fault (E44 on laundry centers is a lid lock communication failure).
Technician
Five minutes unplugged, one more cycle; a repeat needs service.

Front-load: motor, heater and temperature

Code Frigidaire meaning First move
E52, E54, E59 Tachometer signal bad (E52), over speed (E54), no signal (E59).
Technician
Take some laundry out and restart.
E53, E55, E56, E57, E58 Low voltage to the motor board (E53), under speed (E55), high motor current (E56 to E58).
Technician
Unplugged, the drum should turn freely; avoid overloading.
E5A to E5F, E5H Motor board overheated (E5A, E5B, E5C), boards not communicating (E5D, E5E, E5F), low voltage at the motor board on laundry centers (E5H).
Technician
Let it rest unplugged a while.
E66, E68 Heater relay (E66) or heater (E68) on internal-heater models.
Technician
Wash cold until repaired.
E71, E75 Heater temperature sensor (E71) or water temperature sensor circuit (E75).
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
E70, E74, E76 Commonly reported: water supply not seen or cold not entering (E70), wash temperature not rising (E74), cold valve sensor out of range (E76).
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
EF5 Model dependent: load out of balance (laundry centers) or hot valve sensor out of limits (some front-loads). Rebalance and restart.

Front-load: power and controls

Code Frigidaire meaning First move
E67, EA1 to EAE, EB1 to EB3, EH0 to EH3 Wrong voltage at the board (E67) or supply frequency or voltage out of range (EA, EB, EH codes).
Technician
Plug straight into a grounded outlet without an extension cord; an electrician checks the circuit if it persists.
EBE, EBF Motor control or main control board failure.
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
E91 to E9F, E82, E83, E87 Main control, interface, console or motor control not communicating.
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
EF6 Control reset.
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
EF8 Stuck button. Press each key; one that stays stuck means a new interface board.

Top-loaders, laundry centers and older models

Code Frigidaire meaning First move
E1 Top-load: slow fill. Valves open, hoses straight, screens clean.
E2 Top-load: slow drain. Hose and standpipe.
E3 Top-load: lid open or lid lock failed. Close firmly and restart.
E4, E5 Top-load: out of balance (E4) or washer not level (E5). Spread the load; adjust the legs until it stops rocking.
CL Top-load: lid open over 20 seconds with Control Lock on. Close the lid and turn Control Lock off.
E42, EC6, EC7 Laundry centers: lid will not unlock (E42), mode actuator (EC6) or its sensor (EC7).
Technician
Five minutes unplugged, one more cycle; a repeat needs service.
F1, F3, F4, F5 (older) Commonly reported: control fault (F1), water level (F3), not advancing (F4), keypad (F5).
Technician
Five minutes unplugged, one more cycle; a repeat needs service.

What we actually find on Frigidaire washers in the Denver area

The codes above come from Frigidaire’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 8 Frigidaire washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The washer repairs we do most often (all brands)

Our notes on Frigidaire washers are too thin to rank by brand alone, so here is what we found across all 1238 washer calls in our records:

  1. Control or display board: 108 calls
  2. Drain pump: 74 calls
  3. Shock absorbers or suspension: 57 calls
  4. Water inlet valve: 41 calls
  5. Door or lid lock: 28 calls
  6. Door boot seal: 27 calls
  7. Drive belt or coupler: 23 calls

Recent Frigidaire washer calls

  • Boulder (80302), September 2026: Frigidaire washer not draining. Repair: drain pump replaced.
  • Boulder (80302), July 2026: Frigidaire washer not draining. Repair: control or display board replaced.
  • Thornton (80241), January 2025: Frigidaire washer not starting. Repair: drum bearings or spider replaced.

Washer repairs from $240. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Frigidaire washer water inlet valve repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a water inlet valve repair. It is the #4 washer repair on our calls (all brands): 41 calls.
  • Across all 1238 washer calls in our records (all brands), the repairs we do most often: control or display board (108 calls), drain pump (74) and shock absorbers or suspension (57).
  • Recent call: Boulder (80302), September 2026: Frigidaire washer not draining. Repair: drain pump replaced.

Don’t want to do it yourself? Call 720-230-1229.

Frigidaire washer self-checks

  1. Unplug and close both valves.
  2. Reopen the valves fully and clean the hose screens.
  3. On a front-loader, empty the pump filter.
  4. Check the door seal for trapped clothing; level the washer.
  5. Measure HE detergent and run one cycle.

Call a technician when

  • Motor, heater, sensor or board codes keep returning.
  • It fills while unplugged, or leaks.
  • It will not drain with a clean filter and clear hose.
  • The door will not lock or unlock.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frigidaire washer code FAQ

How do I reset a Frigidaire washer?

Unplug it for five minutes, plug it back in and run a cycle.

What does E21 mean?

The washer drains too slowly. Clean the pump filter behind the lower front panel and check the hose.

What does E11 mean?

Filling takes too long. Check both valves, the hoses and the inlet screens.

Are top-load codes the same as front-load codes?

No. Top-loaders use short codes such as E1 to E5, which mean different things from the front-load E-codes.

Sources: searspartsdirect.com, owner.frigidaire.com, owner.frigidaire.com, removeandreplace.com, searspartsdirect.com, searspartsdirect.com, supporthub.aegaustralia.com.au, applianceserviceinfo.com, owner.frigidaire.com, owner.frigidaire.com, owner.frigidaire.com, owner.frigidaire.com. Codes and meanings can vary by model; check your owner’s manual.

720-230-1229
720-230-1229
Call Now Book Online