Frigidaire Dryer Error Codes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

The most common Frigidaire dryer codes are EF1 or E8C (blocked vent or overheating), E42 (door sensing problem), E4A or E5B (long dry time or no heat), E24 or E25 (thermistor fault) and E68 (stuck button). Clean the lint screen and the full vent run first, and check the breakers or gas valve if there is no heat. Motor, heater, sensor and control board codes usually need a technician.

Frigidaire dryers are built by Electrolux, and repair references list the same code families for Frigidaire, Electrolux and Kenmore 417-series dryers. Many models only show codes in service (field test) mode, while newer Gallery and Affinity models may show them on the display. This list combines Electrolux support pages, Sears parts documentation and well-known repair references, so meanings can vary by model; check the tech sheet inside the console. Unplug the dryer, and shut off the gas on gas models, before any hands-on check.

Frigidaire Dryer error codes and what they mean

Code What it means What to try
EF1 Blocked exhaust vent or restricted airflow. Clean the lint screen and the lint buildup around its housing. Unplug the dryer, disconnect the vent, clear it with a vent brush, and make sure the outdoor flap opens. A blocked vent is a fire risk.
E8C / E65 The high-limit thermostat has tripped too often: the dryer is overheating, usually from poor airflow. Clean the lint screen and the full vent run. Check for crushed or kinked ducts behind the dryer. If the vent is clear and the code returns, a technician should check the blower, thermostat and control.
E66 Thermal limiter (thermal fuse) tripped, usually from overheating.
Call a technician
Clear the vent first. The tripped part must be tested and replaced, so request service.
EF3 Maximum dry time expired, often from a blocked vent or a dirty moisture sensor. Clean the lint screen and vent, and wipe the moisture sensor bars inside the drum with rubbing alcohol.
E42 / E40 Door sensing failure: the dryer cannot tell whether the door is open or closed. Close the door firmly and check that nothing is caught in it. If the code persists, the door switch or control board needs testing.
E4A Long dry time: the cycle ran longer than normal, usually from a heating problem.
Call a technician
Clean the lint screen and vent. If the dryer is not heating, the element (electric) or burner parts (gas) need service.
E5B No heat.
Call a technician
Electric: check for a tripped breaker (dryers use two). Gas: make sure the gas shutoff valve behind the dryer is fully open. If there is still no heat, call a technician; do not work on gas parts yourself.
E61 / E63 / E64 Electric heat faults: heater relay failure (E61), heating element shorted to the cabinet (E63), or open heating element, such as a broken coil (E64).
Call a technician
Reset both breakers. If the dryer still does not heat, the element, relay or wiring needs service.
E67 Heating sensor failure on the control.
Call a technician
Unplug for 5 minutes and restart. If it returns, the control board needs service.
E24 / E25 Thermistor (temperature sensor) open or shorted.
Call a technician
Unplug and restart. If the code returns, the thermistor (about 50,000 ohms) or its wiring needs testing.
E71 / E72 / E73 Outlet thermistor failure (E71, E72) or inlet thermistor failure (E73).
Call a technician
Unplug and restart. If the code returns, the thermistor or wiring needs testing.
E31 / E32 Moisture sensor signal too high or too low, often from residue or metal touching the sensor bars. Remove coins or metal from the drum and clean the sensor bars with rubbing alcohol. Use timed dry until it is fixed.
E51 / E52 / E53 / E54 / E74 Drive motor problems: motor relay stuck or failed (E51, E74), motor stopped or will not start (E52), low voltage or centrifugal switch problem (E53), or motor sensing failure (E54).
Call a technician
Remove part of the load and let the motor cool for 30 minutes. With the dryer unplugged, check that the drum turns by hand. If the code returns, call a technician.
E10 / E11 / E12 / EAF Control board communication error or control board failure.
Call a technician
Unplug for 5 minutes, plug back in and run a cycle. If the code returns, the control board needs replacement.
E68 / EF8 A button on the control panel is stuck. Press each button firmly to free it. If it stays stuck, the control or user interface needs replacement.
E91 / E92 / E93 / E94 / E97 Control errors: communication between the user interface and control board (E91), mismatched replacement part (E92), configuration errors (E93, E94) or program mismatch (E97).
Call a technician
Unplug for 5 minutes. If a part was recently replaced, confirm it is correct for your model. If the code returns, request service.
EA1 / EA2 / EA3 / EA4 / EA5 Power problems: frequency out of range (EA1), voltage too high (EA2) or too low (EA3), incorrect terminal block wiring (EA4), or control board defect (EA5).
Call a technician
Have an electrician check the outlet and the cord connection at the terminal block. If power is correct, the control needs service.
E4 / H2 / B2 / H4 / B4 Reported on Electrolux-built dryers with this display style: humidity sensor failed (E4), power supply issue (H2, B2) or incorrect wiring at installation (H4, B4).
Call a technician
For E4, clean the sensor bars and use timed dry. For H2/B2 or H4/B4, have the installer or an electrician check the power supply and cord wiring.

What we actually find on Frigidaire dryers in the Denver area

The codes above come from Frigidaire’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 7 Frigidaire dryer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.

The dryer repairs we do most often (all brands)

Our notes on Frigidaire dryers are too thin to rank by brand alone, so here is what we found across all 983 dryer calls in our records:

  1. Heating element: 88 calls
  2. Drive belt: 35 calls
  3. Idler pulley or drum rollers: 33 calls
  4. Clogged vent or lint: 29 calls
  5. Thermal fuse or thermostat: 27 calls
  6. Control board: 26 calls
  7. Thermistor or sensor: 20 calls

Dryer repairs from $250. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.

Source: The Appliance Team service records, 2023–2026. Customer details removed.

Video: Frigidaire dryer heating element repair

Video by RepairClinic.com

What we see on Denver calls

  • The video shows a heating element repair. It is the most common dryer repair on our calls (all brands).
  • Across all 983 dryer calls in our records (all brands), the repairs we do most often: heating element (88 calls), drive belt (35) and idler pulley or drum rollers (33).

Don’t want to do it yourself? Call 720-230-1229.

What you can safely check yourself

  1. Unplug the dryer before any hands-on check. On gas dryers, do not touch the gas line or burner.
  2. Clean the lint screen and the lint trap housing.
  3. Clear the vent duct to the outside and replace crushed or foil ducts.
  4. Reset both breakers on electric dryers, or check that the gas valve is fully open on gas dryers.
  5. Wipe the moisture sensor bars inside the drum with rubbing alcohol.
  6. For electronic codes, unplug for 5 minutes, then try one more cycle.

When to call a technician

  • Heater, motor, thermistor or control codes return after a reset.
  • The dryer runs but does not heat with a clean vent.
  • Overheating codes (E8C, E65, E66) keep returning with a clear vent.
  • Power or wiring codes (EA codes, H2/B2, H4/B4) appear.
  • You smell gas or burning, or see scorched clothes.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Frequently asked questions

How do I see the error code on my Frigidaire dryer?

Many models only show codes in field test mode, entered with a button and knob sequence printed on the tech sheet inside the console. Newer models may show the code on the display during a fault.

What does E8C mean on a Frigidaire dryer?

E8C means the high-limit thermostat tripped too many times, so the dryer is overheating. A clogged lint screen or vent is the usual cause; clean both and check for crushed ducts.

What does EF1 mean on a Frigidaire dryer?

EF1 points to a blocked vent. Clean the lint screen and housing, clear the vent duct to the outside, and check that the outdoor flap opens.

How do I reset a Frigidaire dryer?

Unplug it or switch off both breakers for 5 minutes, then restore power and start a cycle. If the code returns, the cause still needs attention.

Sources: searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, owner.electrolux.com, appliancepartspros.com, appliancepartspros.com, appliancepartspros.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner's manual.

720-230-1229
720-230-1229
Call Now Book Online