A Kenmore washer speaks the code language of whoever built it. Read the model number: 110 is Whirlpool, 796 is LG, 417 is Frigidaire/Electrolux. Whatever the maker, the frequent problems are the same four: slow fill (F8E1, LF, F20, IE, E11), slow drain (F9E1, F21, OE, E21), a lid or door that will not lock (F5E2, dL, F22, dE, E41) and an off-balance load (uL, UE). Motor, sensor and board codes generally need a technician.
The model label is under the lid on top-loaders, around the door opening on front-loaders, or on the back panel. The digits before the dot pick your table below. Whirlpool-built 110 machines mix F#E# codes, Oasis “F##” codes and older Elite “F/xx” codes; LG-built 796 machines use two-letter codes like IE and OE; Frigidaire-built 417 machines use E## codes. We drew on Sears parts documentation, the makers’ own help pages and repair references, and the tech sheet inside your washer is the tie-breaker. Unplug and close both water valves before any inspection.
Kenmore washer codes, by manufacturer
110 (Whirlpool-built): water, suds and load
| Code | Meaning for this Kenmore | Our advice |
|---|---|---|
F8E1, LF, F30 (Oasis), Wash light |
Slow or no fill. | Faucets fully open, hoses straight and not frozen, inlet screens cleaned with the water off. |
F9E1, Ld, F32 (Oasis), Spin light |
Not drained within roughly 8 to 10 minutes. | Unkink the hose and keep it from going too deep into the standpipe. A clear path with no drain points to the pump. |
F0E2, Sd, Sud, F71 |
Too many suds; extra rinses run. | Measure HE detergent; hard water is no reason to add more. |
F0E5, uL |
Off-balance load. | Spread the load. Heavy banging with normal loads suggests worn suspension rods or springs. |
oL, F70, F0E3 |
Top-loaders: load too big. | Take some items out. |
F0E4 |
Top-loaders: rinse water too hot. | Check the hoses are on the right inlets; otherwise the thermistor. |
HC, F8E5 |
Hot and cold hoses swapped. | Water off, swap, rerun. |
F8E3, F/09, F27 |
Overflow. Technician |
Close the valves. Filling while unplugged = stuck inlet valve; empty tub = level sensor. |
rL, OU, F34 |
Items in the drum during Clean Washer. | Empty it and restart. If it was empty, a worn tub bearing is possible. |
110: lid, door, motor and controls
| Code | Meaning for this Kenmore | Our advice |
|---|---|---|
lid, F81, F5E4, F5E1 |
Top-loaders: lid not closed, or not opened between cycles (F5E4); lid switch fault (F5E1). | Close before Start and open between loads. Persistent: lid lock/switch assembly. |
F5E2, dL, F/dL, F80, F82, F84, F85, F22 |
Lid or door will not lock. | Clear the opening and wipe soap residue off the lock. |
F5E3, dU, F/dU, F83, F29 |
Lid or door will not unlock; forcing a lid open often breaks the lock. Technician |
Unplug five minutes and try again without force. |
F26 |
Older Elite front-loads: door switch, or three cycles without opening the door. | Open and close the door between loads. |
F7E1, F41, F51, F/06, F25 |
Motor speed or rotor position sensing. Technician |
The basket should turn freely; on new installs the shipping bolts must be out. |
F7E5, F7E6, F7E7, F50, F52, F53, F54, F72 |
Shifter (F7E5), motor (F7E6), motor below speed (F7E7), stalled (F50), will not stop (F52), motor control hot or overcurrent (F53, F54), basket will not re-engage for spin (F72). Technician |
Five minutes unplugged and a smaller load. |
F3E1; F3E2, F40, F/05, F24 |
Pressure sensor (F3E1); water temperature sensor (the others). Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
F23, F44 |
Heater fault (older Elite F23) or heater relay (Oasis F44). Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
F1E1, F01, F/14; F1E2 |
Main board or memory; motor control error (F1E2). Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
F2E1, F02, F2E3 |
Stuck key (F2E1), interface failure (F02), board and interface mismatch after a part swap (F2E3). Technician |
Press each key; verify any new part number. |
F/10, F/11, F/15, F28, F31, F33 |
Elite front-loads: motor board overheated (F/10), lost main board (F/11, F28), failed motor board (F/15, F31), drain pump relay (F33). Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
F/13, F30 (Elite) |
Dispenser cannot reach position; you may hear it shifting. Technician |
Unplug and restart. |
F/H, F20, F21 (older Elite) |
Not filling (F/H, F20) or not drained within 8 minutes (F21). | Fill checks for the first two; clean the pump filter for F21. |
796 (LG-built)
| Code | Meaning for this Kenmore | Our advice |
|---|---|---|
IE |
Water level not reached in time. | Faucets, hoses, inlet screens. |
OE |
Draining too slowly. | Unplug and clean the pump filter behind the lower panel. |
UE, uE |
Unbalanced, or too small a load to balance. | Level the washer, add a towel or two, separate heavy and light items. |
dE, dE1, dE2; dL |
Door or lid not detected closed; top-load lid lock failure (dL). | Close firmly and clear the latch. |
FE |
Overflow; pump may run nonstop. Technician |
Water off. Filling while unplugged means a leaking inlet valve. |
PE, tE |
Water level sensor (PE); heater or water temperature thermistor (tE). Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
LE |
Motor locked or thermal overload tripped. Technician |
Lighter load, less detergent, let it cool. |
E6, EE |
Top-load clutch (E6); board memory (EE). Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
Sud, PF, CL, nE / nF |
Suds, power interruption, child lock on, Wi-Fi fault. | Rinse and Spin for Sud; new cycle after PF; hold Child Lock 5 s; washing works without Wi-Fi. |
417 (Frigidaire/Electrolux-built)
| Code | Meaning for this Kenmore | Our advice |
|---|---|---|
E11 |
Slow fill. | Faucets, hoses, screens; make sure the drain hose is not siphoning. |
E13, E14 |
Tub or sensor-hose leak (E13); dispenser drawer open (E14 on some models). Technician |
Shut the drawer; look underneath for water. |
E21, EF1 |
Slow drain (E21) or pump clogged (EF1). | Clean the pump filter and check the drain. |
E23, E24 |
Drain pump relay on the board. Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
E31, E32, E35, E38 |
Pressure sensor not communicating (E31, E32), overfill (E35), air trap clogged (E38). Technician |
Water entering while unplugged means a stuck valve. |
E41 to E4A |
Door open or lock circuit (E47 opened in spin; E44 to E46 can be board faults). | Close firmly, check the seal for clothing. |
E52 to E59, E5A to E5F |
Motor signal, voltage, speed or current faults; motor board overheated or not communicating. Technician |
Smaller load, rest unplugged. |
E67, E68, E71, E75 |
Board voltage (E67), heater (E68), heater sensor (E71), water temperature circuit (E75). Technician |
Five minutes unplugged, one more try; a repeat needs a repair visit. |
E91 to E9F, EA and EB codes |
Board communication; supply frequency or voltage out of range. Technician |
Grounded outlet, no extension cord; electrician if it persists. |
EF2, EF6, EF8 |
Suds (EF2), control reset (EF6), stuck key (EF8). | Less detergent; unplug five minutes; free the key. |
What we actually find on Kenmore washers in the Denver area
The codes above come from Kenmore’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 64 Kenmore washer service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
The Kenmore washer repairs we do most often
Across all 64 Kenmore washer calls, with or without a code on the display:
- Drain pump: 3 calls
- Control or display board: 3 calls
- Shock absorbers or suspension: 2 calls
- Pressure or water-level sensor: 2 calls
- Clogged filter or foreign object: 2 calls
Recent Kenmore washer calls
- Littleton (80122), September 2026: Kenmore washer not draining. Repair: door or lid lock replaced (WP3949238).
- Longmont (80503), July 2026: Kenmore washer making noise. Repair: shock absorbers or suspension replaced (W10257088).
- Erie (80516), September 2025: Kenmore washer door or lid problem. Cause: clogged filter or foreign object, cleared on site.
- Denver (80204), April 2025: Kenmore washer not starting. Repair: control or display board replaced (EBR75092933).
Kenmore washer repairs from $280. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Kenmore washer error codes
Video by Parts Dr
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- The Kenmore washer repairs we do most often across the Denver metro and Boulder County: drain pump (3 calls), control or display board (3) and shock absorbers or suspension (2).
- Recent call: Littleton (80122), September 2026: Kenmore washer not draining. Repair: door or lid lock replaced (WP3949238).
Don’t want to do it yourself? Call 720-230-1229.
Kenmore washer checks before you call
- Note the model prefix (110, 796 or 417).
- Unplug and close both water valves.
- For fill codes, reopen the faucets and clean the inlet screens.
- For drain codes, check the hose and the front-load pump filter.
- Clear the lid or door lock area, even out the load and measure HE detergent.
When a technician is needed
- Motor, sensor or board codes return after the reset.
- No drain with a clean filter and clear hose.
- Water enters while the washer is off, or there is a leak.
- The lid or door stays locked, or you hear grinding or smell burning.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Kenmore washer code FAQ
Who made my Kenmore washer?
The model prefix tells you: 110 Whirlpool, 796 LG, 417 Frigidaire/Electrolux.
How do I reset a Kenmore washer code?
Unplug it for five minutes, plug it back in and start one cycle.
What does OE mean?
On an LG-built 796 Kenmore it means the washer is draining too slowly. Clean the pump filter and check the hose.
What does F21 mean on a Kenmore Elite?
On older Whirlpool-built Elite front-loads it means the washer did not drain within 8 minutes.
Sources: searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, ifixit.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner’s manual.