Kenmore refrigerator codes depend on who built it, shown by the model number prefix: 106 is Whirlpool-built, 795 is LG-built, 253 is Frigidaire/Electrolux-built, and 111 is a newer Kenmore line. Most codes point to a failed temperature sensor (Er FS, OP, SH, C, F1 Hi), a fan problem (Er FF, SY EF) or a defrost problem (Er dH, F dH, F3). These usually need a technician, but a power reset and a check that doors seal and vents are clear come first.
Kenmore refrigerators were built by several manufacturers, and each uses its own code system. Find the model number on the label inside the fresh food section, usually on a side wall or ceiling, and match the three digits before the dot to a group below. This list combines Sears parts documentation, manufacturer support pages and well-known repair references, so meanings can vary by series. Keep the doors closed while you troubleshoot, and keep a thermometer in each compartment to protect your food.
Kenmore Refrigerator error codes and what they mean
| Code | What it means | What to try |
|---|---|---|
How to tell who built your Kenmore |
Model prefix 106 = Whirlpool. 795 = LG. 253 = Frigidaire/Electrolux. 111 = newer Kenmore models with their own flash and display codes. | Read the model number label and match the first three digits to the groups below. |
795 (LG): Er FS / Er rS |
Freezer (FS) or refrigerator (rS) temperature sensor error. Call a technician |
Unplug for 5 minutes and restart. If the code returns, the sensor, wiring or main board needs service. Watch food temperatures in the meantime. |
795 (LG): Er dH / F dH / r dH |
Defrost error: the defrost sensor did not reach about 40°F during defrost. A defrost heater, fuse or board problem is likely. Call a technician |
Look for heavy frost on the freezer back wall. A technician can confirm the failed part. A manual defrost (unplugged, doors open, towels down) can restore cooling for a short time. |
795 (LG): F dS / r dS |
Freezer or refrigerator defrost sensor fault. Call a technician |
Unplug for 5 minutes and restart. If it returns, the defrost sensor or controller needs service. |
795 (LG): Er FF / Er IF / Er CF |
Fan failures: freezer evaporator fan (FF), ice compartment fan (IF) or condenser fan (CF). Call a technician |
Make sure ice or packages are not blocking a fan. Clean dust from the bottom rear condenser area with the fridge unplugged. If the code returns, the fan motor or board needs service. |
795 (LG): Er IS / Er It |
Ice maker sensor fault (IS) or ice maker system error (It). Call a technician |
Turn the ice maker off and on. If the code returns, the ice maker assembly usually needs replacement. |
795 (LG): Er HS / Er SS / Er rt |
Humidity sensor (HS), pantry or deli drawer sensor (SS) or room temperature sensor (rt) fault. Call a technician |
Unplug for 5 minutes and restart. If it returns, the named sensor or its wiring needs service. |
795 (LG): Er gF |
Flow meter error: the water system is not detecting normal flow. | Check that the household water valve is fully open and the line is not kinked. Replace an old water filter. If it continues, the flow meter needs service. |
795 (LG): Er CO / E Od |
Communication error between the main and display boards (Er CO), or Wi-Fi modem failure (E Od). Call a technician |
Unplug for 5 minutes and restart. If the code returns, a board, harness or Wi-Fi module needs service. |
106 (Whirlpool): C (refrigerator or freezer display) |
Temperature sensor (thermistor) failure in the compartment where the C appears. Call a technician |
Unplug for 5 minutes and restart. If C returns, the thermistor or its wiring needs service. |
106 (Whirlpool): CF |
Communication failure between the main control board and the user interface. Call a technician |
Unplug for 5 minutes and restart. If it returns, the wiring or boards need diagnosis. |
106 (Whirlpool): d |
The air damper between the freezer and fresh food section is stuck. Call a technician |
Make sure food is not blocking the air vents. If the fresh food side stays warm while the freezer is cold, the damper needs service. |
106 (Whirlpool): Freezer display flashing 18°F (-8°C) |
Over-temperature condition, often after a power outage. | Check that the cord is plugged in firmly. When the freezer cools down, press a freezer temperature key to clear the display. Check food safety. |
106 (Whirlpool, newer): PO / flashing F / F#E# |
PO: power outage long enough for the freezer to warm to about 18°F. A flashing F with an F#E# code is a control-detected fault. These are Whirlpool's own codes and may appear on newer Whirlpool-built Kenmore models. | For PO, acknowledge the alert and check food. For a flashing F, unplug for one minute and restart; if it returns, write down the code and request service. |
253 (Frigidaire/Electrolux): OP |
A temperature sensor circuit is open. On the freezer display it is the freezer sensor; on the refrigerator display, the fresh food sensor. Call a technician |
Unplug for 5 minutes and restart. If OP returns, the sensor or wiring needs service. |
253: SH |
A temperature sensor is shorted (freezer or refrigerator, depending on which display shows it). Call a technician |
Unplug for 5 minutes and restart. If SH returns, the sensor or wiring needs service. |
253: SY EF |
Evaporator fan circuit failure. The fan that moves cold air may have stopped. Call a technician |
Listen for the fan in the freezer with the door closed. Make sure ice is not blocking it. If the code returns, the fan or control board needs service. |
253: SY CE / SY CF |
Communication failure between the control board and the user interface. Call a technician |
Unplug for 5 minutes and restart. If the code returns, the harness or boards need service. |
253: H / HI / PF / Door Ajar / DI SP |
H or HI: a compartment has been too warm for over an hour. PF: power failure. Door Ajar: a door has been open over 5 minutes. DI SP: ice jam in the dispenser. | Close and check door seals, clear any ice jam from the chute, and press the alarm or Clear button to acknowledge. If temperatures do not recover, request service. |
111 (newer Kenmore, display models): F1 Lo / F1 Hi / r1 Lo / r1 Hi |
Freezer (F1) or refrigerator (r1) temperature sensor failure. Call a technician |
Unplug for 5 minutes and restart. If it returns, the sensor or wiring needs service. |
111: i5 / FD / rD / iD / rt (Lo or Hi) |
Sensor failures: ice maker (i5), freezer defrost (FD), refrigerator defrost (rD), ice room (iD) or ambient room temperature (rt). Call a technician |
Unplug for 5 minutes and restart. If it returns, request service. |
111: dr / dF |
Refrigerator (dr) or freezer (dF) door switch problem, or a door has been open over an hour. | Close the doors and check that nothing is keeping them from sealing. If the code returns with doors shut, the door switch needs testing. |
111: F3 / r3 |
Freezer (F3) or refrigerator (r3) defrost heater failure. Call a technician |
Check for heavy frost on the evaporator cover. The heater or its wiring needs service. |
111: C1 |
Sealed refrigerant system failure, such as low refrigerant or a bad compressor. Call a technician |
Call a technician. Refrigerant work requires certified recovery and recharge; it is never DIY. |
111: ES / d2 |
ES: dispenser fault, often a stuck Water or Ice button. d2: forced defrost mode, which ends on its own. | For ES, press the dispenser buttons to free a stuck one. For d2, no action is needed; the fridge returns to normal cooling after defrost. |
111 (top-freezer, no display): control board light flashes 1, 2, 3, 4 or 6 times |
1 = refrigerator sensor, 2 = ambient sensor, 3 = defrost sensor, 4 = door open over 1 hour, 6 = defrost heater failure. Call a technician |
For 4 flashes, close the door and check the door switch. For the others, unplug for 5 minutes; if the flashing returns, request service. |
What we actually find on Kenmore refrigerators in the Denver area
The codes above come from Kenmore’s own documentation. This section shows what our technicians found once they opened the machine. Since 2023 we have handled 75 Kenmore refrigerator service calls across the Denver metro and Boulder County. Every number here comes from our own job records.
The Kenmore refrigerator repairs we do most often
Across all 75 Kenmore refrigerator calls, with or without a code on the display:
- Compressor or sealed system: 9 calls
- Evaporator or condenser fan: 6 calls
- Control or inverter board: 5 calls
- Ice maker: 3 calls
- Water inlet valve: 3 calls
- Damper: 2 calls
Recent Kenmore refrigerator calls
- Erie (80516), August 2026: Kenmore refrigerator leaking. Repair: compressor or sealed system replaced.
- Longmont (80503), August 2026: Kenmore refrigerator ice maker not working. Diagnosis: ice maker.
- Longmont (80501), April 2026: Kenmore refrigerator not starting. Repair: damper replaced.
- Denver (80249), February 2026: Kenmore refrigerator freezer not freezing. Repair: evaporator or condenser fan replaced.
Kenmore refrigerator repairs from $200. Home diagnostic visit from $59, credited toward your repair. Call 720-230-1229.
Source: The Appliance Team service records, 2023–2026. Customer details removed.
Video: Kenmore refrigerator error codes
Video by SimpleDIY
What we see on Denver calls
- An error code points to the system that reported the fault, not always to the part that failed.
- The Kenmore refrigerator repairs we do most often across the Denver metro and Boulder County: compressor or sealed system (9 calls), evaporator or condenser fan (6) and control or inverter board (5).
- Recent call: Erie (80516), August 2026: Kenmore refrigerator leaking. Repair: compressor or sealed system replaced.
Don’t want to do it yourself? Call 720-230-1229.
What you can safely check yourself
- Find the model number and note the prefix (106, 795, 253 or 111) so you read the right code list.
- Do a power reset: unplug or switch off the breaker for 5 minutes, then restore power.
- Make sure doors close fully and gaskets are clean, and that food is not blocking air vents.
- Unplug the fridge and vacuum dust from the condenser coils and grille at the bottom.
- Check that the household water valve is open and the filter is not overdue.
- Keep a thermometer in each compartment: 37°F for the fridge and 0°F for the freezer.
When to call a technician
- A sensor, fan, defrost or board code returns after a power reset.
- The fridge is above 40°F or the freezer above 10°F for several hours.
- You see heavy frost on the freezer back wall or hear fans stop.
- A sealed system code (C1) appears or the compressor runs but nothing cools.
- You hear clicking, buzzing or a compressor that starts and stops repeatedly.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Frequently asked questions
Who makes my Kenmore refrigerator?
Check the model number prefix on the label inside the fridge. 106 is Whirlpool-built, 795 is LG-built, and 253 is Frigidaire/Electrolux-built. The prefix tells you which code list applies.
What does Er FF mean on a Kenmore refrigerator?
On LG-built 795 models, Er FF means the freezer fan has a problem. Make sure ice is not blocking the fan; if the code returns after a reset, the fan motor or control board needs service.
What does SY EF mean on a Kenmore refrigerator?
On Frigidaire-built 253 models, SY EF is an evaporator fan circuit failure. Without that fan, the fresh food section warms up even if the freezer stays cold.
How do I reset my Kenmore refrigerator?
Unplug it or switch off its breaker for about 5 minutes, then restore power. Some models also have a Clear Alerts or alarm button for temperature and door alarms.
Sources: searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, searspartsdirect.com, owner.frigidaire.com, producthelp.whirlpool.com, producthelp.whirlpool.com, ifixit.com, appliancepartspros.com. Codes and meanings can vary by model; check your owner's manual.



