Commercial Dishwasher Repair in Denver

Undercounter, door-type and glasswashers, high-temp and low-temp. Same-day or next-day visits, a $129 diagnostic credited to the repair, and a 90-day warranty.

Same-Day Service 90-Day Warranty $129 Diagnostic

Commercial dishwasher repair for restaurants, cafes, school kitchens, senior living, clubs and offices in 52 Denver-area cities. We repair undercounter dish machines, door-type (hood) machines and glasswashers, both high-temp and low-temp chemical units. A commercial diagnostic is $129 and is credited to the repair if you go ahead. Below are real jobs from our service tickets, with photos our technicians took on site.

$129commercial diagnostic, credited to the repair
Same / next daycommercial calls get priority
90 dayswarranty on parts and labor
Early startwe can come before service starts

Dish machines we work on

Tell us which type you have when you call. It changes which parts we bring and how long the visit takes.

Undercounter dish machines

The most common machine in cafes, bars, small restaurants, school kitchens and office pantries. One rack at a time, two to three minute cycles. Brands we see most are CMA and Kromo, along with Hobart, Jackson and Champion. Because the pump, heater and chemical feeds are packed into a small cabinet, leaks and drain problems are the usual calls.

Door-type (hood) machines

The upright machine in a dish room with tables on both sides; you slide the rack in and pull the hood down. High volume, and the kitchen stops when it stops. Fill and drain valves, wash motors, door switches, heaters and chemical pumps are the parts we work on most.

Glasswashers

Bar glasswashers work like a small undercounter machine and fail the same way: drain, fill, heat and sanitizer. Low water temperature and a missing sanitizer dose show up as cloudy glasses long before the machine stops.

Conveyor and flight machines

Larger rack conveyor machines in hotels, hospitals and big kitchens. Call us and describe the machine; we will tell you on the phone whether it is a job for us.

High-temp or low-temp: why it matters for the repair

A high-temp machine sanitizes with very hot final rinse water, around 180°F, made by a booster heater. If the booster heating element, its thermostat or its contactor fails, the machine still washes, but the dishes are no longer sanitized and a health inspector will write it up. A low-temp machine sanitizes with a chemical, usually chlorine, dosed by a small pump. If that pump or its tubing fails, the dishes look clean and are not sanitized. That is exactly what happened in Longmont: the machine ran normally but was not pumping the sanitizer solution through. We test both: rinse temperature with a gauge on high-temp machines, and the sanitizer level with test strips on low-temp ones, before and after the repair.

Many low-temp machines have detergent and sanitizer pumps that belong to a chemical supplier. If the fault is in the supplier’s equipment, we say so, show you what we found and you call them. If it is in the machine, we fix it.

What we actually find on commercial dishwasher calls

Wash chamber of a commercial undercounter dishwasher with wash arms and drain checked in Boulder

Water left in the tank: drain pump and drain line

Undercounter machines pump water out with a drain pump. When the pump fails or the drain line clogs, water stays in the tank and the next cycle starts dirty. In a Boulder school kitchen the drain pump had failed; we replaced it and ran the machine through several full cycles. Food scraps, broken glass and labels from containers are what usually kill drain pumps, so keep the strainer basket in place.

Signs: standing water after the cycle, slow draining, a humming pump, an error at the end of the cycle.

Leaking on the floor: drain system, gaskets and switches

A CMA undercounter machine in Boulder was leaking. We traced the leak to the drain system, repaired it and replaced a faulty switch sensor that was letting the machine run when it should not. Door gaskets, hose clamps under the tank and a cracked drain fitting are the other usual sources. We find the leak before we replace anything; a wet floor is not a diagnosis.

Signs: water on the floor after each cycle, water under the machine, a wet cabinet.

Not sanitizing: chemical pump, tubing, booster

On the Longmont door-type machine the sanitizer was not getting through. The pump needed work and a line had to be replaced; after that we checked the dose with test strips. On high-temp machines, the same symptom comes from the booster heater: rinse water that never reaches temperature.

Signs: no chemical smell, sanitizer jug never empties, test strip shows nothing, final rinse temperature low.

Will not fill or overfills: fill valve and float

A fill solenoid that does not open leaves the tank empty and can burn out the heater. One that does not close overfills the tank and runs water to the drain all day. We check the valve, the float or pressure switch that tells the board the level, and the water pressure coming in.

Signs: tank empty at the start of a cycle, water running constantly, the machine stuck on fill.

Dirty or spotty dishes: wash arms, temperature, scale

Clogged wash arm nozzles, a missing end cap, low wash temperature or scale on the heater and arms all leave food on plates and spots on glasses. Sometimes the fix is cleaning, sometimes it is a wash pump or heater. We check temperature and spray first, because they cost nothing to check.

Signs: food left on plates, film on glasses, wash arms that do not spin freely.

Will not start: door switch, controls, power

A machine that does nothing when you close the door usually has a door switch, a fuse, a float that thinks the tank is empty, or a control board problem. We test each before we order a part.

Signs: no lights, lights but no wash, the cycle starts and stops immediately.

Brands and what we see on them

CMA. CMA undercounter and door-type machines are common in Colorado cafes, bars and small kitchens, many of them low-temp chemical machines. On the ones we service, leaks from the drain system, switch faults and chemical feed problems come up most.

Kromo. Italian-built undercounter machines with a drain pump, wash pump and built-in heaters in a compact cabinet. The drain pump is the part we have replaced on these; the strainer in front of it is what protects it.

Hobart, Jackson and Champion. The big names in door-type and undercounter machines. They share the same systems: fill valve, wash pump, tank heater, booster or chemical pump, drain, and a control that ties them together. We diagnose them the same way: fill, wash, heat, sanitize, drain, one step at a time.

If your machine is a brand not listed here, call anyway and tell us the brand. If it is not something we can fix, we will say so on the phone instead of sending a technician to find out.

Booster heaters and tank heaters

High-temp machines have two heaters: the tank heater that keeps wash water hot, and the booster that lifts the final rinse to sanitizing temperature. When the booster fails, the machine keeps running and the dishes still look clean, so the problem is often found by a staff member reading the gauge, or by an inspector. We check the heating element, the thermostat, the high-limit safety and the contactor that switches the element. A contactor with burnt contacts is a common and inexpensive cause; a scaled-up element that has burnt out is the other. After the repair we run several cycles and watch the rinse temperature at the gauge.

Hard water, scale and deliming

Every dish machine builds scale, and the hotter the water, the faster. Scale coats the heaters so they take longer to heat, blocks wash and rinse nozzles, and makes glasses look cloudy. Most manufacturers call for deliming on a schedule that depends on your water; in busy kitchens that can be every week or two. If you see white crust inside the tank or on the arms, delime before you call us, then see whether the problem is still there. If it is, it is a part, and we will find it.

How a commercial dishwasher service call works

  1. Call or book onlineTell us the type of machine (undercounter, door-type, glasswasher), high-temp or low-temp, and what it is doing. A photo of the whole machine helps us bring the right parts.
  2. Same-day or next-day visitCommercial calls get priority, and we can come before your service starts. The $129 diagnostic is credited to the repair if you approve it.
  3. Written quote before workWe check fill, drain, wash, heat and sanitizer, then quote the repair before we start.
  4. Repair and full cycle testWe replace the part, run full cycles with racks, and check temperature or sanitizer level before we leave.
  5. If a part must be orderedWe tell you how long it takes and whether the machine can run safely until then.

From our service tickets

Longmont · door-type, low-temp

Sanitizer not pumping through

The machine washed normally but the sanitizer solution was not getting into the rinse. Pump repaired, line replaced, dose checked with test strips.

Boulder · undercounter, school kitchen

Water staying in the tank

The drain pump had failed. New pump installed and the machine tested through full cycles before the kitchen’s next service.

Boulder · CMA undercounter

Leaking under the machine

The leak came from the drain system. We repaired it and replaced a faulty switch sensor.

Boulder · CMA undercounter

Not working properly

The same kitchen called us earlier for this machine not running correctly. We repaired it, and they called us again when it started leaking.

What decides the price of a dishwasher repair

Every commercial call starts with the $129 diagnostic, credited to the repair when you approve it. After that, the price depends on the part and the machine. Switches, gaskets, fill valves and chemical tubing are the smaller repairs. Drain pumps, wash motors, booster heating elements and control boards are the bigger ones. Access matters too: an undercounter machine built into a bar takes longer to pull out than a door-type machine standing in a dish room. You get a written quote before any work starts, and nothing is added without your OK.

Repair or replace?

A commercial dish machine is built to be repaired. Pumps, motors, heaters, valves and boards are all available for the common brands, so repair is usually the right call. Replacing makes sense when the tank or frame is corroded through, when parts are no longer made for an old model, or when the machine cannot keep up with your volume any more. If we think that is where you are, we tell you on the spot, with the repair price next to it.

Health inspections and your dish machine

Inspectors check that dishes are actually sanitized: the final rinse temperature on a high-temp machine, the chemical level on a low-temp one, and the temperature or test strip log your staff keep. A machine that “looks fine” can fail on either. If an inspection is coming up, or you got written up, call us. We check the machine, fix what is wrong and show your staff how to test it.

Daily habits that prevent most calls

  • Scrape plates before racking. Food is what clogs drain pumps and wash arms.
  • Keep the strainer and scrap basket in place and empty them every shift.
  • Drain the tank and clean the wash arms at the end of the day.
  • Delime on schedule; scale on heaters and arms makes everything work harder.
  • Check final rinse temperature or sanitizer level each shift and write it down.
  • Call us at the first leak or slow drain, before it becomes a closed kitchen.

Quick checks before you call

  • Is the water supply valve open and the drain not backed up into the floor sink?
  • Is the door fully closed and the strainer seated?
  • Did a breaker trip?
  • Is the detergent or sanitizer jug empty, or is the pickup tube out of the jug?

If those are fine and the machine is still down, call us and tell us what you see. It speeds up the visit.

Where we fix commercial dishwashers

Denver, Boulder, Longmont, Broomfield, Louisville, Lafayette, Westminster, Arvada, Lakewood, Golden, Wheat Ridge, Englewood, Littleton, Centennial, Aurora, Highlands Ranch, Parker, Thornton and the rest of the metro. See all service areas.

Related commercial services

Dish machine problems we fix

01
Water left in the tank, not draining
02
Leaking onto the floor
03
Sanitizer or detergent not dispensing
04
Final rinse not reaching temperature
05
Will not fill or keeps filling
06
Dirty or spotty dishes and glasses
07
Machine will not start or stops mid-cycle
08
Deliming, wash arms and preventive service
Commercial Dishwasher Repair in Denver
Pricing

How much does commercial dishwasher repair in Denver cost in Denver?

Commercial diagnostics are $129, credited toward the repair. You get a written quote before any work starts, and repairs carry our 90-day parts and labor warranty.

$129Diagnostics, credited to repair
WrittenQuote before work
90 daysParts & labor warranty
See full price list →
Brands We Service

What Customers Say About Our Commercial Appliance Repairs

4.9 from 691 reviews · 546 on Google

★★★★★Google review
“Our commercial freezer Arctic air was not cooling. A technician from this company performed diagnostics. It turned out that the compressor needed to be replaced. The next day they did everything. Now everything works perfectly. A month later we contacted The Appliance Team again, because there were
— Sergii Chetverikov
★★★★★Google review
“The Appliance Team is FANTASTIC! We have used them for two separate appliance fixes: refrigerator and freezer not cooling and our dishwasher not draining. They always have someone available to pick up the phone, so there is no need to leave voicemails and wait to hear back. They are available
— Aaron B
★★★★★Google review
“Technician informed me of his progress as to when he would arrive. Arrived on time and performed service in a reasonable amount of time. Explained what he was doing and how to maintain the fridge. Refrigerator runs just like it should now... very satisfied.”
— Christopher Conklin

Read all reviews on Google →

Frequently Asked Questions

Commercial diagnostics are $129 and are credited toward the repair. After diagnosis you get a written quote for parts and labor before any work begins, and every repair has a 90-day parts and labor warranty.

Usually the drain pump has failed or the drain line is blocked by food, glass or labels. On gravity-drain machines the drain valve or the floor sink can be the problem. We check the strainer, the line and the pump, and replace only what has actually failed.

On a high-temp machine the booster heater, its thermostat or its contactor is the usual cause, and the rinse gauge shows it. On a low-temp machine the sanitizer pump or its tubing has stopped feeding chlorine. We test temperature or sanitizer level before and after the repair.

We see CMA and Kromo most often, and we work on Hobart, Jackson, Champion and other undercounter, door-type and glasswasher machines. If your brand is not listed, call and tell us the brand; we will say on the phone whether we can help.

Yes. Commercial calls get priority, usually the same or the next day, and we can schedule an early visit so the dish room is running before service. If a part has to be ordered, we tell you how long it takes and whether the machine can run safely until then.

Dish machine down? Get it washing again.

Call now for same-day or next-day commercial dishwasher repair in Denver and the metro. $129 diagnostic, credited to the repair.

Other Services We Offer

Photos from our dishwasher repair calls

Real photos our technicians took on repair calls around Denver. Each caption names the city where the job was.

Dishwasher repair in Castle Pines, photo from our job records
Dishwasher repair in Castle Pines
Dishwasher repair call in Erie
Dishwasher repair call in Erie
Dishwasher repair call in Arvada
Dishwasher repair call in Arvada
Dishwasher repair call in Denver
Dishwasher repair call in Denver
Dishwasher repair call in Arvada
Dishwasher repair call in Arvada
Dishwasher repair call in Boulder
Dishwasher repair call in Boulder

From our job videos

A short clip filmed by our own technician on a real job. Noisy GE stackable washer-dryer at a salon: transmission, motor and shocks replaced. Wheat Ridge.

Reviewed by Zach, appliance technician at The Appliance Team, EPA 608-certified. Written from our own service records. About our technicians · Updated November 2026

720-230-1229
720-230-1229
Call Now Book Online