Maytag Washer Not Draining? F9E1, F21 and Real Fixes

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

A Maytag washer that will not drain usually has a clogged drain filter or pump, a drain hose that is kinked or came loose, or a drain pump that has failed. On our Maytag calls around Denver we replaced drain pumps, cleaned the drain system and filter, repaired pump wiring, replaced door locks and drain hoses, and on two machines replaced the control board. F9E1, F21 or LD on the display all point to a drain that takes too long.

Maytag washers, especially the Maytag front-loaders and the big top-loaders, are common in Denver-area laundry rooms. Since January 2024 our technicians have taken about 15 Maytag washer calls where the washer would not drain, from Arvada and Westminster to Erie, Broomfield and Longmont. Here is what to check and what we found.

Checks you can do yourself

  1. Front-loaders: clean the drain filter. It is behind the small door at the bottom front. Put towels down and drain slowly into a pan before you unscrew it fully.
  2. Check the drain hose. Make sure it is not kinked, crushed against the wall or pulled out of the standpipe. On a Louisville call the hose was not held in place, fell out and leaked onto the floor.
  3. Check the standpipe or laundry sink for a clog.
  4. Reset. Unplug the washer for a few minutes and run Drain & Spin.
  5. Listen to the pump. Humming without water moving means a jam; a loud grinding means debris in the impeller; no sound means power or the pump motor.
Maytag front-load washer on a pedestal in Westminster
Maytag front-loader in Westminster showing F9E1 and not draining: we cleaned the drain system.

What we found on Maytag “not draining” calls

Date City Problem What we found or did
Nov 2026 Arvada Humming noise, not draining Replaced the drain pump and the control board
Sep 2026 Erie Leaking, LD code (long drain) Replaced the main control board
Jun 2026 Louisville Stopping mid-cycle, water on the floor Drain hose was not secured and fell out
Mar 2026 Westminster F9E1, not draining Cleaned the drain system
Jan 2026 Englewood F21 code Drain filter was clogged; cleaned it
Dec 2025 Longmont Top-loader full of water, would not start Repaired the drain pump wires
Dec 2025 Littleton Not draining or spinning Transmission needed to be replaced
Nov 2025 Broomfield F2 error and SUD Replaced the drain pump
Sep 2025 Boulder Door lock problem Replaced the door lock and the drain hose
Jul 2025 Longmont Not draining Replaced the drain hose, cleaned the drain pump
Mar 2025 Arvada Top-loader not draining Replaced the drain pump and the lid latch
Dec 2024 Denver One-year-old washer, error, not spinning Replaced the drain assembly
Maytag top-load washer with the lid open in an Erie laundry room
Maytag top-loader in Erie with an LD (long drain) code and a leak: the main control board was replaced.

Clogs and the drain pump

Most Maytag drain calls start with a clog: lint, a sock, coins or too much detergent residue. If the filter is cleaned in time, the pump survives, as in Englewood and Westminster. If the washer keeps running against a clog, the pump overheats and fails, and we replace it, as in Arvada, Broomfield and Denver. A humming pump that never moves water is the typical sign.

White Maytag front-load washer in a Broomfield laundry room
Maytag front-loader in Broomfield with an F2 error and SUD: drain pump replaced.

When it is not the pump

  • Control board. On an Arvada top-loader and an Erie washer with an LD code, the control board was part of the repair.
  • Wiring. On a Longmont top-loader the washer was full of water and would not start; the wires to the drain pump were repaired.
  • Door lock or lid latch. The washer will not drain and spin if it cannot lock. We replaced a door lock in Boulder and a lid latch in Arvada.
  • Drain hose. A loose or damaged hose leaks and drains poorly, as in Louisville and Longmont.
Maytag top-load washer in an Arvada laundry room
Maytag top-loader in Arvada that would not drain: drain pump and lid latch replaced.

From the technician

“On a Maytag front-loader I always check the filter first, and I show the customer where it is. Cleaning it every month or two would save a lot of these service calls. And make sure the drain hose is clipped into the standpipe; if it pops out during the drain, you get a flood.” — Zach, technician at The Appliance Team

Repair cost and booking

Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Questions we hear on Maytag drain calls

Why is my Maytag washer not draining?

A clogged drain filter or pump, a kinked or loose drain hose, or a failed drain pump are the most common causes. Less often, the pump wiring, a door lock or the control board.

What do F9E1, F21 and LD mean on a Maytag washer?

All three mean the washer took too long to drain. Clean the drain filter and check the hose first. If the code comes back, the drain pump usually needs to be cleaned or replaced.

How do I reset my Maytag washer?

Unplug it for a few minutes, plug it back in and run Drain & Spin. If it still does not drain, a part is jammed or has failed.

Is it worth fixing a Maytag washer that won’t drain?

Usually yes. Clearing a clog is quick, and a drain pump is a moderate repair. Our technician tells you the price before starting.

See also our guide: Maytag washer not spinning: what we find on real calls.

From our job videos

A short clip filmed by our own technician on a real job. Samsung washer: water valve replaced. Denver.

720-230-1229
720-230-1229
Call Now Book Online