GE Dishwasher Not Draining? FTD Code and What We Find

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

A GE dishwasher that will not drain is usually a clogged filter or drain pump, a plugged drain hose or check valve, or a drain pump that has failed. On more than 30 GE “not draining” calls around Denver, the drain pump was the part we replaced most often. If the display shows FTD, the dishwasher could not drain in time. Clean the filter and check the drain hose under the sink first; if water still stays, the pump needs to be cleaned or replaced.

GE is one of the most common dishwasher brands in Denver metro homes, and it is the brand we see most for drain problems. Since January 2024 our technicians have logged more than 30 GE dishwasher calls where water stayed in the tub, from Longmont and Thornton to Littleton and Centennial. Here is what we check, and what we actually found.

Signs your GE dishwasher is not draining

  • Water standing on the tub floor after the cycle ends.
  • The cycle does not finish, or the dishwasher stops and shows FTD or another code.
  • Water draining onto the floor, or a leak under the dishwasher at the same time as poor draining.
  • Dishes coming out with grit or a film, which often means dirty water stayed in the tub during the wash.
GE dishwasher control panel showing the FTD code
GE dishwasher in Erie showing FTD on the display. Cleaning the drain pump fixed it; the lower spray arm was also replaced.

Checks you can do yourself

Turn the power off at the breaker before you reach into the tub or under the sink.

  1. Clean the filter. Pull out the lower rack, twist out the filter at the bottom of the tub and rinse it. Scrub the fine screen with a soft brush.
  2. Scoop out the water and look around the drain opening for glass, bones, seeds or labels.
  3. Check the drain hose under the sink for kinks and make sure it rises in a high loop before it reaches the disposal or drain.
  4. Run the garbage disposal. A full disposal backs water up into the dishwasher. If the disposal is new, the knockout plug in its dishwasher inlet may still be in place.
  5. Restart the cycle and listen during the drain. A hum with no water moving points to a jammed pump; silence points to a failed pump or a control problem.

What we found on GE “not draining” calls

Date City Problem What we did
Oct 2026 Longmont Not draining, error code Replaced the drain pump
Sep 2026 Westminster Not completing the cycle Replaced the drain pump and the pressure sensor
Apr 2026 Erie FTD on the display Cleaned the drain pump, replaced the lower spray arm
Mar 2026 Thornton Not finishing the cycle Replaced the control board, heating element and drain pump
Nov 2025 Golden Water not draining Control board needed to be replaced
Sep 2025 Littleton Not draining Replaced the drain hose, drain pump and check valve
Aug 2025 Lafayette Not draining completely Replaced the drain pump assembly
Jun 2025 Centennial Leaking Replaced the drain pump
Apr 2025 Longmont Not draining Replaced the pressure sensor
Apr 2025 Erie Drain problem Cleaned the drain pump
Jan 2025 Centennial No longer draining Drain pump housing needed to be replaced
Dec 2024 Thornton Portable dishwasher draining weakly Cleaned the drain hose
Sep 2024 Parker FTD on the display Repaired the drain hose and the water pressure sensor
Old and new drain pump from a GE dishwasher repair
The old and the new drain pump from a GE dishwasher in Lafayette that would not drain completely.

The parts behind most GE drain problems

  • Drain pump. The part we replaced most often. A jammed impeller can sometimes be cleared, as on our Erie calls; a worn or burned-out pump has to be replaced.
  • Drain hose and check valve. A clogged hose or a stuck check valve lets water flow back into the tub. In Littleton we replaced both along with the pump.
  • Pressure sensor. GE uses a sensor to measure the water level. When it fails, the dishwasher can stop the cycle or report a drain problem even with a good pump. We replaced it in Longmont and Westminster.
  • Control board. Less common, but if the board does not send power to the pump, nothing drains. We found this in Golden and Thornton.
Stainless GE dishwasher in a Westminster kitchen
GE dishwasher in Westminster: it stopped before the end of the cycle. Drain pump and pressure sensor replaced.

From the technician

“With GE I always check the pressure sensor along with the pump. If you only change the pump and the sensor is bad, the dishwasher still stops with a drain error and the customer thinks the repair did not work. Also, if your dishwasher is built in tight, tell us when you call. Some units are hard to pull out of the cabinet, and we plan the visit around it.” — Zach, technician at The Appliance Team

White GE dishwasher in a Centennial kitchen
GE dishwasher in Centennial that was leaking: drain pump replaced.

Repair cost and booking

Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities, including Longmont, Thornton, Erie, Westminster, Littleton and Centennial.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Questions we hear on GE drain calls

Why is my GE dishwasher not draining?

On our calls the usual causes were a clogged filter or drain pump, a plugged drain hose or check valve, a failed drain pump, a failed pressure sensor and, less often, the control board.

What does FTD mean on a GE dishwasher?

The dishwasher could not drain in the expected time. Clean the filter and check the drain hose first. If the code comes back, the drain pump or the pressure sensor usually needs attention.

How do I make my GE dishwasher drain?

On most models, press Start/Reset (or Cancel) and the dishwasher drains for a minute or two. If it does not, clean the filter and check the hose with the power off.

Is it worth replacing the drain pump on a GE dishwasher?

Usually yes. The drain pump is one of the most common dishwasher repairs, and the rest of the machine is often fine. Our technician tells you the price before starting.

From our job videos

A short clip filmed by our own technician on a real job. GE dishwasher with no power: we replaced the user interface board. Frederick.

720-230-1229
720-230-1229
Call Now Book Online