Whirlpool Washer Not Spinning? What We Find on Real Calls

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

When a Whirlpool washer will not spin, first make sure it drained, the lid locks (on top-loaders) and the load is balanced. On our Whirlpool calls around Denver the parts behind spin problems were a worn motor coupling on older top-loaders, a failed control board, worn shock absorbers or suspension rods, and on one new front-loader the shipping bolts that were never removed. A grinding noise at the end of the spin points to the suspension or the drum and needs a technician.

Whirlpool makes a large share of the washers in Denver-area homes, including Maytag, Amana, Kenmore and Kirkland-branded machines. Since January 2024 our technicians have taken more than a dozen Whirlpool washer calls about spin problems: not spinning at all, not finishing the spin, or spinning loudly. Here is what to check and what we found.

Checks you can do yourself

  1. Check for water in the tub. If it did not drain, it will not spin. Look for a kinked drain hose or a clogged standpipe. Front-loaders also have a coin trap or drain filter behind the lower front panel.
  2. Check the lid or door. A top-loader will not spin if the lid lock does not engage. Look for something stuck in the latch.
  3. Balance the load. Spread heavy items out or wash them with a few towels, then run Drain & Spin.
  4. New washer? Remove the shipping bolts. Front-loaders ship with transport bolts in the back. If they stay in, the drum cannot move and the washer bangs and shakes in spin.
  5. Reset. Unplug it for a few minutes and run Drain & Spin. If it still does not spin, a part has failed.
White Whirlpool top-load washer in a Brighton laundry room
Whirlpool top-load washer in Brighton that would not spin.

What we found on Whirlpool spin calls

Date City Problem What we found or did
Nov 2026 Denver Noise in spin Drum frame rusted at the bottom and sagging
Jun 2026 Erie Loud grinding at the end of the final spin Installed an upgraded suspension rod kit
Jun 2026 Denver Kirkland (made by Whirlpool) would not go into spin Diagnosed
Dec 2025 Longmont Older top-loader not spinning Motor coupling
Jul 2025 Lakewood Not spinning Shock absorbers and control board housing needed
May 2025 Longmont Loud noise while spinning (new washer) Shipping bolts were never removed; removing them fixed it
Apr 2025 Longmont Not spinning Control board needed to be replaced

Older top-loaders: the motor coupling

Whirlpool direct-drive top-loaders connect the motor to the transmission with a small plastic coupling. It is made to break if the washer is overloaded, which protects the motor and the transmission. When it breaks, the motor hums or runs but the tub does not agitate or spin. On a Longmont call the coupling was the reason the washer stopped spinning. It is a quick, inexpensive repair on these machines.

Older Whirlpool direct-drive top-load washer in Longmont
Older Whirlpool top-load washer in Longmont: it stopped spinning because of the motor coupling.

Newer washers: suspension, control board and shipping bolts

  • Suspension rods and shocks. Worn suspension lets the tub swing and hit the cabinet, so the washer slows or stops the spin to protect itself. In Erie a loud grinding at the end of the final spin went away with an upgraded rod kit; in Lakewood worn shock absorbers were part of the problem.
  • Control board. If the board does not command the spin, nothing happens even though everything else works. We found this in Longmont and Lakewood.
  • Shipping bolts. On a new front-loader in Longmont the bolts were still in place, and the washer made a loud noise in spin. Removing them solved it.
  • Drum frame. On an older Denver washer the frame at the bottom had rusted, and the drum sagged. That is usually the point where replacing the washer makes more sense.

From the technician

“On a Whirlpool that won’t spin, check the lid switch and the drain before anything else. On the older direct-drive models, the coupling is the first thing I look at. On new front-loaders, I’ve seen the shipping bolts left in more than once, so look at the back panel before you call anyone.” — Zach, technician at The Appliance Team

Repair cost and booking

Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Questions we hear on Whirlpool spin calls

Why won’t my Whirlpool washer spin?

Check the drain, the lid lock and the load balance first. On our calls the parts behind it were a motor coupling, the control board, suspension rods or shocks, and on a new washer the shipping bolts.

How do I reset my Whirlpool washer?

Unplug it for a few minutes, plug it back in and run Drain & Spin. If it still will not spin, a part has failed.

Why does my Whirlpool washer make a loud noise when spinning?

Worn suspension rods, shocks or a drum bearing; on a new washer, shipping bolts left in place. A frame that has rusted at the bottom can also cause it.

Is it worth fixing a Whirlpool washer that won’t spin?

A coupling, lid lock, rods or shocks are usually worth fixing. A rusted frame or a failed drum bearing on an older washer often is not. Our technician tells you the price first.

From our job videos

A short clip filmed by our own technician on a real job. Whirlpool washer with F8E1 and F3E2 errors: water inlet valve replaced. Denver.

720-230-1229
720-230-1229
Call Now Book Online