A Samsung washer that will not spin is most often off balance (a UB code), not draining, or has worn suspension rods, a broken spider arm or a bad drum bearing. Water must drain out before the drum can spin, so if water is left in the tub, start with the drain. On our Samsung calls around Denver we replaced suspension rods and shocks, a spider arm, drain pumps, and once found a pressure hose that had come off the tub.
Samsung washers, both top-load and front-load, are among the machines we see most in Denver-area laundry rooms. Since January 2024 our technicians have closed more than 20 Samsung washer calls where the drum would not spin, spun badly or stopped during spin. Here is what we check first and what we actually found.
Checks you can do yourself
- Rebalance the load. One heavy item (a rug, a comforter, a pair of jeans in a small load) can stop the spin and show UB. Spread the load evenly, or add a couple of towels, and run a Rinse+Spin.
- Check that it drained. If water is still in the tub, the washer will not spin. On front-loaders, clean the small drain filter behind the lower front panel (have towels ready). Check the drain hose for kinks.
- Make sure it is level. A washer that rocks on one foot shakes hard in spin and may stop. Adjust the feet so all four touch the floor.
- Reset the washer. Unplug it for a few minutes. On one call the fix was a calibration after a reset.
- Listen in spin. Scraping, grinding or a loud roar points to the bearing or the spider arm and needs a technician.

What we found on Samsung “not spinning” calls
| Date | City | Problem | What we found or did |
|---|---|---|---|
| Sep 2026 | Longmont | Not spinning and not draining | Drain pump |
| Mar 2026 | Golden | Does not spin, leaks a little | Pressure hose had come off the tub |
| Feb 2026 | Boulder | UB code in spin with light loads | Replaced the suspension rods |
| Dec 2025 | Longmont | Not spinning | Bad drum bearing and spider arm; door boot leaking |
| Oct 2025 | Littleton | Stackable washer stuck, not spinning | Clogged drain; cleaned it |
| Oct 2025 | Arvada | Drum spinning hard, smoke | Replaced the spider arm |
| Apr 2025 | Denver area | Won’t spin | Washer calibration |
| Jan 2025 | Westminster | Not spinning, water left inside | Drain pump |
| Dec 2024 | Lakewood | Not spinning, clothes wet | Suspension rods needed |
| May 2024 | Broomfield | Not washing, rinsing or spinning well | Shocks |
Top-load Samsung: balance, suspension rods and the pressure hose
Samsung top-loaders hang the tub on four suspension rods. When the rods wear out, the tub swings too far in spin, hits the cabinet and the washer stops with a UB code, even with a normal load. Replacing the rods as a set fixes it. On a Golden call the washer did not spin and leaked a little because the pressure hose had come off the tub: without it, the washer cannot tell how much water is inside.

Front-load Samsung: spider arm, bearing and shocks
On a front-loader the drum is held by a three-arm aluminum spider bolted to the back of the drum. With age it corrodes and cracks, and the drum starts to wobble, scrape or spin hard. On an Arvada call the washer started smoking and the drum was spinning hard; the spider arm was replaced. In Longmont the drum bearing was worn as well, which usually shows up first as a loud roar in spin. Worn shocks make the washer bang and stop in spin.

From the technician
“With a Samsung that won’t spin, I always look at the water first. If there’s water in the tub, it’s a drain problem, not a spin problem. If it’s dry and throws UB with small loads, it’s almost always the suspension. A roar in spin is the bearing, and that’s when you decide repair or replace.” — Zach, technician at The Appliance Team
Repair cost and booking
Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities.
- Call 720-230-1229 and tell us the model, top-load or front-load, and the code on the display.
- See our Samsung washer repair page, the Samsung washer error codes or the general washer not spinning guide.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Questions we hear on Samsung spin calls
Why is my Samsung washer not spinning?
The usual causes are an unbalanced load, water not draining, worn suspension rods or shocks, a broken spider arm, a bad drum bearing, or a sensor hose that came off.
What does UB mean on a Samsung washer?
UB means unbalanced. Spread the load out and run Rinse+Spin. If UB shows up with normal or light loads, the suspension rods or shocks are usually worn.
Why does my Samsung washer have water in it and won’t spin?
It cannot spin until the water drains. Check the drain filter on front-loaders and the drain hose. If it still does not drain, the drain pump usually needs to be replaced.
Is it worth fixing a Samsung washer that won’t spin?
Suspension rods, shocks, a drain pump or a hose are moderate repairs and usually worth it. A spider arm or bearing is a bigger job; our technician tells you the price first so you can decide.
See also our guide: Samsung washer not draining: what we find on real calls.