Whirlpool Dishwasher Not Draining? What to Check First

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

A Whirlpool dishwasher that leaves water in the tub most often has a clogged filter, a plugged or badly routed drain hose, or a drain pump that is jammed or failing. On our Whirlpool calls around Denver, cleaning the filter and drain hose or clearing the pump impeller fixed most of them; one needed a high loop added to the drain hose. Start with the filter and the hose under the sink, and if the pump hums or rattles without draining, call a technician.

Whirlpool dishwashers are everywhere in Denver-area homes, from older units in rentals to new ones in remodels. Since January 2024 our technicians have taken about a dozen Whirlpool dishwasher calls where water stayed in the tub, in Westminster, Lakewood, Arvada, Parker, Erie, Denver and other cities. Most of them did not need a new pump. Here is what we check and what we found.

Checks you can do yourself

Turn the power off at the breaker before you reach into the tub or under the sink.

  1. Clean the filter. Most Whirlpool dishwashers made in the last ten years have a two-part filter at the bottom of the tub. Twist the upper filter out, lift the lower screen, and rinse both. A filter that has never been cleaned is the most common reason for slow draining.
  2. Remove standing water with a cup and a towel and look for glass, seeds or bones near the drain opening.
  3. Check the drain hose under the sink: no kinks, and a high loop up under the counter before it connects to the disposal or drain.
  4. Check the disposal. Run it to clear the line. If it was just installed, make sure the knockout plug was removed.
  5. Run a drain. On most models, press Cancel or Cancel/Drain and the dishwasher drains for about two minutes. Listen to the pump.
Whirlpool dishwasher in a Lakewood kitchen after a drain repair
Whirlpool dishwasher in Lakewood: it was full of water and the pump rattled. We cleaned the drain pump impeller and it drained again.

What we found on Whirlpool “not draining” calls

Date City Problem What we did
Jan 2026 Lakewood Tub full of water, pump rattling Cleaned the drain pump impeller
Nov 2025 Arvada Drain and heating problems Repaired the drain pump, replaced the heating element
Oct 2025 Westminster Water collecting in the bottom after a few days Added drain hose and set up a high loop
Feb 2025 Denver Water left after the cycle and a puddle while running Diagnosed drain and leak together
Jan 2025 Parker Not draining Cleaned the drain hose
Dec 2024 Denver Not working properly Cleaned the drain hose
Dec 2024 Erie Would not drain Cleaned the filter and the drain hose

Water in the bottom after the dishwasher sits

If the dishwasher drains fine at the end of the cycle but water shows up again a day or two later, the water is coming back from the sink drain. On a Westminster call this happened because the drain hose had no high loop, so water from the sink flowed back into the dishwasher. We added hose and set up the loop under the counter, and it stopped. This is also why a dishwasher can smell bad between loads.

When it is the drain pump

  • Rattling or grinding on drain: something is caught in the impeller. On our Lakewood call, cleaning the impeller blades solved it.
  • Humming with no water moving: the impeller is jammed or broken.
  • No sound at all: the pump motor, its wiring or the control is not working.

Whirlpool, KitchenAid, Maytag and many Kenmore dishwashers share the same drain pump designs, so the repair is similar across these brands. See also our KitchenAid dishwasher not draining guide.

From the technician

“A lot of Whirlpool drain calls come down to a filter that has never been taken out. Pull it out once a month and rinse it. And if the dishwasher was just installed and never drained right, check the hose loop and the disposal plug before anything else.” — Zach, technician at The Appliance Team

Repair cost and booking

Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Questions we hear on Whirlpool drain calls

Why is my Whirlpool dishwasher not draining?

Most often a clogged filter, a plugged or kinked drain hose, a blocked disposal connection, or debris in the drain pump. A failed pump is less common than people expect.

How do I force my Whirlpool dishwasher to drain?

On most models, press Cancel or Cancel/Drain, and it drains for about two minutes. If nothing happens, clean the filter and check the hose with the power off.

Why is there water in my Whirlpool dishwasher a day after it ran?

Water is coming back from the sink drain. The drain hose needs a high loop under the counter, or an air gap, so sink water cannot flow back in.

Is it worth fixing a Whirlpool dishwasher that won’t drain?

Usually yes. Many drain problems are fixed by cleaning, and a new drain pump is a moderate repair. Our technician tells you the price before starting.

From our job videos

A short clip filmed by our own technician on a real job. Dishwasher control panel job in Longmont.

720-230-1229
720-230-1229
Call Now Book Online