When a KitchenAid dishwasher leaves water in the tub, check three things in this order: the filter at the bottom of the tub, the drain hose (kinks, the garbage disposal connection, the air gap), and then the drain pump. On our KitchenAid “not draining” calls around Denver where the cause was recorded, cleaning a clogged filter or drain pump fixed more than half; the rest needed a new drain pump or drain hose. An F9E1 code on the display means the dishwasher took too long to drain.
KitchenAid dishwashers are in a lot of Denver metro kitchens, and “it stopped draining” is one of the main reasons we get called to them. Since January 2024 our technicians have closed 123 KitchenAid dishwasher jobs, and draining problems came up on about 15 of them, from Golden and Westminster to Aurora and Parker. This guide walks through what we check first, what you can safely do yourself, and when the drain pump is the problem.
Is your KitchenAid really not draining?
- A little water under the filter is normal. The sump below the filter always holds some water. If you only see it after you take the filter out, the dishwasher is fine.
- Standing water on the tub floor after a full cycle is not normal. The water is leaving too slowly or not at all.
- The cycle stops, beeps or runs for hours. Many KitchenAid models stop the cycle and show a drain code when the water does not go down in time.
- Dirty or gritty dishes. A slow drain often shows up as dishes that come out with a film before you ever see standing water.
What we found on KitchenAid “not draining” calls
These are real KitchenAid dishwasher jobs from our records, with the cause our technician wrote down. Customer names and addresses are never published.
| Date | City | What we found | What we did |
|---|---|---|---|
| Jul 2026 | Golden | F7E1 and F9E1 codes, water not draining | Cleaned the filter |
| Apr 2026 | Westminster | Not draining | Replaced the drain pump |
| Jan 2026 | Parker | Cycle not finishing, F9E1 code | Cleaned the filter; later replaced the circulation pump for an F7E1 code |
| Jan 2026 | Golden | Drain error code | Drain pump and drain hose needed replacement |
| Sep 2025 | Boulder | Not draining | Cleaned the drain pump |
| Aug 2025 | Broomfield | Not draining, several error codes | Replaced the drain pump |
| Jan 2025 | Aurora | Water not pumping out | Cleaned the drain pump and hose, ran calibration |
| Dec 2024 | Denver | Water left in the tub | Cleared a clogged drain pump |
| Oct 2024 | Aurora | Dishwasher not working | Replaced the drain pump |
The pattern is clear: on a KitchenAid, the water path is filter, drain pump, drain hose. Debris that gets past a dirty filter ends up in the pump, and a pump that has been fighting a clog for months often fails.

Checks you can do yourself
Turn the dishwasher off at the breaker or unplug it before you reach into the tub or under the sink.
- Clean the filter. Pull out the lower rack, twist the filter at the bottom of the tub counterclockwise and lift it out. Rinse it under the tap and scrub the fine mesh with a soft brush. Two of our KitchenAid drain calls ended right here.
- Look into the sump. With the filter out, scoop out the standing water with a cup and a towel and look for glass, bones, seeds, labels or a lost cap near the drain opening.
- Check the drain hose under the sink. It should run up in a high loop before it connects to the disposal or the drain. A kinked or flattened hose, or a hose pushed down behind the cabinet, slows the drain.
- Check the garbage disposal connection. If the disposal was just replaced, the knockout plug inside its dishwasher inlet may still be in place. Run the disposal too, since a full disposal backs water up into the dishwasher.
- Clean the air gap if you have one (the small cap next to the faucet). Pull the cover off and clear any gunk.
- Run a drain. On most KitchenAid models, press Cancel (or Cancel/Drain) and the dishwasher drains for about two minutes. Listen for the pump.
If you hear the pump hum but the water stays, or you hear nothing at all, the drain pump is the next suspect, and it is time to call us.

What the KitchenAid drain codes mean
| Code | What it usually means | Check first |
|---|---|---|
| F9E1 | The dishwasher took too long to drain | Filter, drain hose, disposal connection, then the drain pump |
| F7E1 | Problem with the wash motor (circulation pump) | Usually needs a technician |
To read a code, watch the display or the blinking lights after the cycle stops. Codes can differ by model, so if you are not sure, give us the code and the model and we will tell you what it points to. Our KitchenAid dishwasher error code guide lists more of them.
When it is the drain pump
- The pump hums but no water moves. The impeller is jammed or broken.
- No sound at all on drain. The pump motor or its wiring has failed, or the control is not sending power.
- The filter and hose are clean, and the code keeps coming back. The pump cannot move water fast enough anymore.
- Water under the dishwasher. On one Broomfield call our technician also saw water under the unit, so the area around the pump and hose was checked too.
A clogged pump can sometimes be cleared and reused, as on our Boulder, Aurora and Denver calls. A worn or broken pump gets replaced. On most KitchenAid dishwashers the pump is reached from under the tub, so the dishwasher usually has to be pulled out of the cabinet. One Boulder dishwasher was set so deep in the cabinet that the floor would have had to be opened to remove it, so check how the unit was installed if you are planning a remodel.

From the technician
“Most KitchenAid drain calls start with a filter that has not been cleaned in a long time. People do not know there is a filter at all. Rinse it once a month and scrape plates before loading, and the pump lives a lot longer. If the dishwasher still stops with F9E1 after a clean filter, do not keep restarting it. A pump that runs against a blockage overheats and fails.” — Zach, technician at The Appliance Team

Repair cost and booking
Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician finds the cause and gives you the price for the repair before any work starts. We work in 52 Denver-area cities, including Golden, Westminster, Broomfield, Boulder, Aurora and Parker.
- Call 720-230-1229 and tell us the model and the code on the display.
- See our KitchenAid dishwasher repair page or the general dishwasher not draining guide.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Questions we hear on KitchenAid drain calls
Why is there water in the bottom of my KitchenAid dishwasher?
A little water under the filter is normal. Standing water on the tub floor after a cycle usually means a clogged filter, a kinked or plugged drain hose, a blocked garbage disposal connection or a failing drain pump.
How do I make my KitchenAid dishwasher drain?
On most models, press Cancel or Cancel/Drain, and the dishwasher drains for about two minutes. If it does not, turn the power off, clean the filter and check the drain hose under the sink.
What does F9E1 mean on a KitchenAid dishwasher?
F9E1 means the dishwasher took too long to drain. Start with the filter and the drain hose. If the code comes back, the drain pump usually needs to be cleaned or replaced.
Is it worth replacing the drain pump on a KitchenAid dishwasher?
Usually yes. A drain pump is one of the more affordable dishwasher repairs, and the rest of the machine is often in good shape. Our technician will tell you the price before starting, and the diagnostic fee is credited toward the repair.