Maytag Washer Not Spinning? What We Find on Real Calls

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

When a Maytag washer will not spin, first make sure it drained and the lid or door locks. On our Maytag calls around Denver, the causes were a worn transmission or a broken motor coupling and shift actuator on top-loaders, a failed control board, and on one front-loader a broken drum spider that locked the drum. If the agitator moves but the basket barely turns, the transmission is the usual suspect.

Maytag top-loaders and front-loaders are common in Denver-area homes. Since January 2024 our technicians have taken more than a dozen Maytag washer calls where the washer would not spin, from Longmont and Lakewood to Littleton, Erie and Denver. Here is what to check and what we found.

Checks you can do yourself

  1. Make sure it drained. A washer with water inside will not spin. See our Maytag washer not draining guide if water is left in the tub.
  2. Close the lid or door firmly. The washer will not spin unless it locks.
  3. Balance the load. Spread out heavy items and run Drain & Spin.
  4. Turn the basket by hand with the power off. If it will not move at all on a front-loader, something inside is locked up.
  5. Reset. Unplug the washer for a few minutes. Write down any code on the display.
White Maytag front-load washer in a Longmont laundry room
Maytag front-loader in Longmont: the drum was stuck and would not turn even by hand.

What we found on Maytag spin calls

Date City Problem What we found or did
Sep 2026 Denver Not finishing the spin, F7E6 and F7E7 codes Diagnosed, parts ordered
Jun 2026 Longmont Front-loader drum stuck, would not turn by hand Spider arm stuck on the drum bearings; basket and rear drum replaced
Jan 2026 Lakewood Agitator moving fast, basket barely turning Transmission needed to be replaced
Dec 2025 Littleton Not draining or spinning Transmission needed to be replaced
Jun 2025 Longmont Not spinning Control board needed to be replaced
Dec 2024 Denver One-year-old washer, error, stopped Replaced the drain assembly
Oct 2024 Erie Not spinning Replaced the motor coupling and the shift actuator

Top-loaders: coupling, shift actuator and transmission

On many Maytag top-loaders, a shift actuator switches the transmission between agitate and spin, and a coupling connects the motor to it. If the actuator fails, the washer agitates but never shifts into spin. If the coupling breaks, the motor runs and nothing turns. On an Erie call we replaced both. When the transmission itself wears out, the agitator can move while the basket barely turns, as on our Lakewood and Littleton calls; that is a bigger repair, and on an older washer it is worth comparing with the price of a new one.

Older Maytag top-load washer in an Erie laundry room
Maytag top-loader in Erie that would not spin: motor coupling and shift actuator replaced.

Front-loaders: spider and bearings

A front-loader drum is held by an aluminum spider bolted to its back and supported by bearings in the rear tub. If the spider corrodes and breaks, it can jam against the bearing area and lock the drum. On a Longmont Maytag the drum would not turn even by hand; the spider arm had stuck on the drum bearings, and the basket and rear drum were replaced.

Corroded spider and bearing area from a Maytag front-load washer
The spider and bearing area from the Longmont Maytag: the spider arm had stuck on the drum bearings.

Control board

If the washer fills and agitates but never gets the command to spin, and the mechanical parts check out, the control board is next. We found this on a Longmont top-loader.

Maytag top-load washer in a Lakewood laundry room
Maytag top-loader in Lakewood: the agitator moved fast but the basket barely turned. The transmission was worn.

From the technician

“On a Maytag top-loader that agitates but won’t spin, I check the shift actuator and the coupling before I talk about a transmission. They’re much cheaper parts. On a front-loader, if you can’t turn the drum by hand, stop using it right away and call.” — Zach, technician at The Appliance Team

Repair cost and booking

Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Questions we hear on Maytag spin calls

Why won’t my Maytag washer spin?

Water left in the tub, a lid or door that does not lock, a broken coupling or shift actuator, a worn transmission, a failed control board, or on front-loaders a broken spider.

Why does my Maytag agitate but not spin?

On many top-loaders, the shift actuator is not switching the washer into spin, or the transmission is worn.

How do I reset my Maytag washer?

Unplug it for a few minutes, plug it back in and run Drain & Spin. If it still will not spin, a part has failed.

Is it worth fixing a Maytag washer that won’t spin?

A coupling, actuator or board is usually worth it. A transmission or spider on an older washer often is not. Our technician tells you the price before starting.

From our job videos

A short clip filmed by our own technician on a real job. Samsung washer: water valve replaced. Denver.

720-230-1229
720-230-1229
Call Now Book Online