When a Whirlpool washer will not drain, check the drain filter (front-loaders), the drain hose and the house drain first. If water still stays, the drain pump is the usual cause: jammed with socks, coins or lint, or failed. On our Whirlpool calls around Denver we cleaned clogged pumps and filters, replaced drain pumps, repaired a pump wire harness, and replaced a water level sensor, a lid lock and a control board. F9E1 on the display means the washer took too long to drain.
Whirlpool washers, top-load and front-load, are in a lot of Denver-area homes, and drain problems are one of the most common reasons we get called to them. Since January 2024 our technicians have taken about 20 Whirlpool washer calls where water stayed in the drum or the washer showed a drain code, from Longmont and Boulder to Arvada, Wheat Ridge and Denver.
Checks you can do yourself
- Front-loaders: clean the drain filter. Open the small panel at the bottom front, put down towels and a shallow pan, and unscrew the filter slowly. Socks, coins, hair ties and lint collect here.
- Check the drain hose. It should not be kinked behind the washer, and it should not be pushed too far down into the standpipe.
- Check the house drain. If the washer drains into a laundry sink or standpipe that is clogged, water backs up or spills. On one Denver call the washer was fine; the sink it drained into was clogged.
- Top-loaders: check the lid. Some models will not drain and spin if the lid lock is not working.
- Run Drain & Spin and listen for the pump. A hum with no water moving means the pump is jammed; silence means it is not getting power.

What we found on Whirlpool “not draining” calls
| Date | City | Problem | What we found or did |
|---|---|---|---|
| May 2026 | Longmont | Not draining, F9E1 | Repaired the drain pump wire harness |
| Feb 2026 | Arvada | Top-loader leaking and not draining | Replaced the drain pump |
| Jan 2026 | Lafayette | Drain error | Control board needed |
| Oct 2025 | Longmont | Not working, E1 and F9 codes | Clogged drain; cleaned the drain pump and filter |
| Sep 2025 | Boulder | Duet front-loader, F9E1 | Cleaned the drain pump |
| Sep 2025 | Wheat Ridge | Stacked front-loader, several codes | Replaced the water level sensor; drain pump repaired |
| Sep 2025 | Longmont | Not draining | Drain pump needed to be replaced |
| Jul 2025 | Denver | Water spilling | The sink the washer drains into was clogged |
| Jun 2025 | Mead | Draining all the time | Control board needed |
| Jun 2025 | Denver area | Not draining | Replaced the lid lock |
| Jan 2025 | Longmont | Cabrio top-loader, drain error | Replaced the drain pump |
| Oct 2024 | Denver | F21 code | Replaced the drain pump |
Front-loaders: pump and filter
On Whirlpool and Duet front-loaders, anything that comes out of pockets ends up in the drain filter or the pump. A small sock or a coin can stop the impeller completely. On our Boulder and Longmont calls, cleaning the pump and filter was enough. When the pump motor has burned out, or the impeller is broken, the pump is replaced.

Top-loaders: drain pump, lid lock and board
Newer Whirlpool and Cabrio top-loaders have no user-accessible filter, so a jam goes straight to the pump. We replaced pumps in Arvada and Longmont. Other parts can stop the drain too: a lid lock that does not engage, a broken wire to the pump (Longmont), or a control board that does not run the pump correctly (Lafayette, Mead).

When the sensor is the problem
A Whirlpool washer uses a pressure (water level) sensor to know how much water is inside. If it reads wrong, the washer may think it is still full and keep trying to drain, or stop with a set of codes. On a Wheat Ridge stacked unit the water level sensor was replaced along with work on the drain pump.

From the technician
“Before you call, open the drain filter on a front-loader. A lot of the time there’s a sock in it. If it’s a top-loader, check where the hose goes. If the laundry sink or standpipe is slow, the washer gets blamed for a plumbing problem.” — Zach, technician at The Appliance Team
Repair cost and booking
Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities.
- Call 720-230-1229 and tell us the model and the code on the display.
- See our Whirlpool washer repair page, the Whirlpool washer error codes or the general washer not draining guide.
How to prevent this
Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:
Questions we hear on Whirlpool drain calls
Why is my Whirlpool washer not draining?
A clogged drain filter or pump, a kinked hose or a clogged house drain are the common causes. On our calls, failed drain pumps, a broken pump wire, a lid lock, a water level sensor and the control board were the parts we replaced.
What does F9E1 mean on a Whirlpool washer?
F9E1 means the washer took too long to drain. Clean the drain filter on a front-loader and check the hose and the house drain. If it comes back, the drain pump usually needs to be cleaned or replaced.
How do I drain a Whirlpool washer full of water?
Turn it off and unplug it. On a front-loader, drain the water slowly through the drain filter or the small drain tube next to it into a shallow pan. On a top-loader, you may need to bail the water out or lower the drain hose into a bucket.
Is it worth fixing a Whirlpool washer that won’t drain?
Usually yes. Cleaning a pump or filter is quick, and a new drain pump is a moderate repair. Our technician tells you the price before starting.