LG Washer Not Spinning? UE, DE and Real Repairs

Updated November 2026 · By Zach, EPA 608-certified appliance technician, The Appliance Team, Denver CO

Quick answer

When an LG washer will not spin or stops the spin early, the usual causes on our Denver-area calls were a drain pump that could not empty the drum, worn shock absorbers or suspension, a failed sensor (vibration or hall sensor), a door lock problem (DE code) and, on older machines, a worn drum bearing. A UE code means unbalanced; a u5 on one ThinQ washer pointed to the vibration sensor. Check the load balance and the drain filter first.

LG front-loaders, WashTowers and top-loaders are among the most common washers in Denver-area homes. Since January 2024 our technicians have taken more than 20 LG washer calls about spin problems, from Erie and Boulder to Lone Tree, Arvada and Littleton.

Checks you can do yourself

  1. Balance the load. LG washers try several times to balance before they give up and show UE. Spread out heavy items or add a few towels.
  2. Clean the drain pump filter. On front-loaders it is behind the small panel at the bottom front. A clogged filter stops the drain, and the washer will not spin with water inside.
  3. Close the door firmly. A DE code means the washer does not detect a closed and locked door.
  4. Check that the washer is level and all four feet touch the floor.
  5. Reset. Unplug for a few minutes, then run Rinse+Spin. Note any code.
LG front-load washer in a Lone Tree laundry room
LG front-loader in Lone Tree that would not reach high-speed spin with heavy loads: suspension shocks replaced.

What we found on LG spin calls

Date City Problem What we found or did
Nov 2026 Denver ThinQ washer not spinning, u5 code Replaced the vibration sensor
Sep 2026 Boulder Not draining, spinning with a noise Diagnosed drain and spin together
May 2026 Erie Squeaking and shaking hard in spin Replaced the shocks
May 2026 Lone Tree No high-speed spin with heavy loads Replaced the suspension shocks
Mar 2026 Boulder Not going into spin, DE code Door lock problem
Dec 2025 Erie Not spinning Replaced the hall sensor
Dec 2025 Littleton Not spinning Replaced the drain pump
Dec 2025 Arvada Top-loader LE code, drum barely turning, noise Worn drum bearing
Jun 2025 Longmont Loud noise in spin Replaced the drain pump
Mar 2025 Lafayette Won’t spin, noise Replaced the drain pump
Mar 2025 Boulder Spin problem Replaced the suspension
Feb 2025 Boulder Quit spinning Bearing and water valve needed
Feb 2024 Centennial Spinning too loud Cleaned the drain pump; replacement recommended

Drain pump problems that look like spin problems

An LG washer drains before every spin. If the pump is clogged or weak, the drum stays wet and the washer will not spin, or spins with a loud noise. On our Littleton, Longmont and Lafayette calls the fix for a “won’t spin” complaint was a new drain pump. Cleaning the filter regularly prevents a lot of these.

Black LG front-load washer in an Erie laundry room
LG front-loader in Erie that squeaked and shook hard in spin: shocks replaced.

Suspension and shocks

LG front-loaders hang the tub on springs and sit it on shock absorbers. Worn shocks let the tub move too much, so the washer cannot balance and refuses to reach full speed, or squeaks and shakes. We replaced shocks in Erie, Lone Tree and Boulder.

Sensors, door lock and motor

  • Vibration sensor: on a Denver ThinQ washer showing u5, the vibration sensor was replaced.
  • Hall sensor: LG direct-drive motors use a hall sensor to read the rotor position. When it fails, the drum may not spin. We replaced one in Erie.
  • Door lock: a DE code stops the spin. On a Boulder washer the door lock was the problem.
  • Drum bearing: a roaring noise in spin and a drum that barely turns point to the bearing, as on an Arvada top-loader. On an older washer this is often the point to consider replacement.
LG WashTower in a Denver laundry room
LG ThinQ washer in Denver showing u5 and not spinning: vibration sensor replaced.

From the technician

“With LG, check the drain pump filter before anything else. A lot of ‘it won’t spin’ calls are really ‘it can’t drain’. If it shakes and squeaks, it’s the shocks. And if it roars in spin, that’s the bearing; stop running it before the tub gets damaged.” — Zach, technician at The Appliance Team

White LG front-load washer in an Erie laundry room
LG front-loader in Erie that stopped spinning: hall sensor replaced.

Repair cost and booking

Our diagnostic visit is from $59 for homes, and the fee is credited toward the repair if you go ahead. The technician tells you the price before any work starts. We work in 52 Denver-area cities.

How to prevent this

Many of these breakdowns start with maintenance that was skipped. These guides show what to check, how often, and what happens if you don't:

All appliance maintenance guides →

Questions we hear on LG spin calls

Why is my LG washer not spinning?

An unbalanced load, a clogged drain pump or filter, worn shocks, a failed sensor, a door lock problem or, on older washers, a worn bearing.

What does UE mean on an LG washer?

UE means the load is unbalanced. Spread the load out and run Rinse+Spin. If UE shows with normal loads, the shocks or suspension may be worn.

What does DE mean on an LG washer?

DE is a door error: the washer does not detect a closed and locked door. Close it firmly; if the code stays, the door lock or switch needs attention.

Is it worth fixing an LG washer that won’t spin?

A drain pump, shocks or a sensor are usually worth fixing. A bearing on an older washer often is not. Our technician tells you the price before starting.

From our job videos

A short clip filmed by our own technician on a real job. LG washer spin noise check. Boulder.

720-230-1229
720-230-1229
Call Now Book Online