GE Refrigerator Repair

GE refrigerator repair in Denver — not cooling, control and inverter boards, fans, frost, ice makers and leaks. We repair GE and GE Profile French-door, side-by-side, bottom-freezer and top-freezer refrigerators across Denver and 30 nearby cities, 24/7, including sealed-system work.

4.9★ on Google · $99 service call waived with the repair · Written quote before any work · 90-day warranty on parts and labor · EPA 608 certified technicians · Same-day or next-day visits

Since January 2024 we have completed 256 GE refrigerator calls, more than any other refrigerator brand except LG. About half started with “not cooling” or “stopped working.” When we look at what actually fixed them, the same parts come up again and again: the main control board or the compressor’s inverter board, the evaporator fan, and the defrost heater.

1. GE refrigerator not cooling

On GE refrigerators, “not cooling” usually comes down to one of these. We check them in this order, cheapest and most likely first:

• Evaporator fan. The fan behind the freezer panel moves cold air into the fridge. When it stops, the freezer often stays cold while the fresh-food side warms up. A fan that grinds or buzzes is often on its way out.
• Frost on the evaporator. A failed defrost heater, sensor or defrost control lets ice build up on the coil until air can’t get through.
• Main control board. On newer GE models the board runs the fans, defrost and compressor. A failed board can make the refrigerator look completely dead.
• Inverter board. Many GE refrigerators use a variable-speed compressor driven by a separate inverter board. When that board fails, the compressor doesn’t start, even though the compressor itself is fine. It is a much cheaper repair than a compressor.
• Condenser coil and fan. Dust on the coil under the refrigerator, or a stopped condenser fan, makes the compressor overheat and shut off.
• Sealed system. A refrigerant leak or a failed compressor. Less common, and the most expensive repair, so we rule out everything above first.

Check these first. Food-safety guidance is to keep the fresh-food section at 40 °F or below and the freezer at 0 °F. After changing a setting, give the refrigerator a full day to settle. Make sure the doors close fully and food isn’t blocking the vents inside.

2. Ice maker not making ice

• Water supply. A clogged water filter or a failing water inlet valve starves the ice maker. If water from the dispenser is slow, start there.
• Freezer temperature. If the freezer isn’t cold enough, the ice maker won’t cycle. Ice melting in the bucket points to a cooling problem.
• The ice maker itself. Motors and sensors wear out. Replacing the ice maker assembly is a common, straightforward repair.

3. Water leaking

• Inside, under the drawers, or ice on the floor of the freezer. A clogged or frozen defrost drain. The water from defrosting has nowhere to go.
• On the floor. A leaking water inlet valve, a cracked water line, or the water filter housing.

From our service log

• October 2024, not cooling. The compressor wasn’t running, but the compressor was fine: the inverter board that drives it had failed. A new inverter board fixed it.
• June 2024, fridge at 60 °F, freezer at 20 °F. We cleaned the condenser coils and the fan and reset the temperature control. No parts were needed.
• May 2025, “it makes noise.” The evaporator fan was failing. We replaced it and the noise stopped.
• February 2025, refrigerator not working. The defrost control board and the compressor’s relay capacitor had failed. We replaced both.
• April 2025, ice maker not working. We replaced the ice maker assembly.

Error codes and the display

Many GE refrigerators don’t show an error code at all; the display just keeps showing the set temperatures while the inside warms up. Some newer models can show diagnostic codes, but they vary by model and GE doesn’t publish one list for all of them, so check your owner’s manual. If your refrigerator shows a code, write it down before you call. It helps us bring the right part.

Code still on the display? Call 720-230-1229. We answer 24/7 and can usually be there the same or next day.

Find your GE model number

On most GE refrigerators the label is inside the fresh-food section, on a side wall near the top or on the ceiling. GE refrigerator model numbers often start with GFE or GNE for French-door, GSS or GSE for side-by-side and GTE or GTS for top-freezer; GE Profile models often start with P.

Still having trouble with your GE refrigerator? Call 720-230-1229. We answer 24/7 and can usually be there the same or next day.

Repair or replace?

Fans, defrost parts, ice makers, inlet valves, control boards and inverter boards are almost always worth repairing on a GE refrigerator. A failed compressor or refrigerant leak on an older unit is where we give you an honest repair-versus-replace number. Either way, you get a written quote before any work starts, and the $99 service call is waived if you go ahead with the repair.

GE refrigerator repair near you

We repair GE refrigerators in Denver and every city we serve across the metro, with same-day or next-day visits. Tap your city to see local service details:

Related: GE appliance repair · Refrigerator repair · Ice maker repair · Whirlpool refrigerator repair